R1387 DCM2461/SCRIGNO - OPEN2.0 | pagina 50
Open 2.0
EN
Before commissioning
IMPORTANT
• Remember that the Antamatic® system must be tested before it is put
into service so that a declaration of correct installation and conformity can
be issued.
• Carefully fill in the declaration of conformity and provide a copy to the
Customer
EC Declaration of Conformity: SIR S.r.l. declares that this product
complies with the requirements and relevant provisions of Directives
2006/42/EC, 2014/30/EC and 2014/35/EC. A certified copy of the
original is available by contacting SIR S.r.l.
Disposal Information
IMPORTANT
• Remember that the Antamatic® system must be disconnected from the
power supply by qualified personnel.
• Interrupt the power supply before carrying out the disconnection
operation.
• Initiate environmentally friendly recycling of rechargeable batteries,
accessories and packaging that are no longer usable.
• Do not dispose of electrical appliances and rechargeable batteries/
batteries as household waste!
• EC countries only:
According to European Directive 2012/19/EU, power tools
that have become unusable and, according to European
Directive 2006/66/EC, defective or worn-out batteries and
rechargeable batteries must be collected separately and sent
for ecological reuse.
Maintenance information
IMPORTANT
• Remember that before cleaning and/or servicing the Open Antamatic®
system, the power supply must be disconnected.
The Antamatic® system does not require any special maintenance. In case
of faults, contact the Sir S.r.l. after-sales service.
• Sir S.r.l. disclaims all liability in case of maintenance operations carried
out by unqualified personnel.
GENERAL SAFETY INFORMATION
CAUTION
Read all hazard warnings and operating instructions. Failure to follow
the hazard warnings and operating instructions may result in danger of
electric shock and/or serious accident.
Keep all hazard warnings and operating instructions in a safe place for
future reference.
The manual must cover the entire life of the Antamatic® system until it is
disposed of.
Keep plastic bags out of the reach of children: danger of suocation!
Before starting installation
IMPORTANT
• Remember that the OPEN 2.0 Antamatic® kit, made by Sir srl, must be
installed only by qualified personnel; Sir srl disclaims liability in case of
installation of the system by unauthorized or unqualified personnel;
• Before starting system installation, the installer is reminded to fully
comply with the minimum safety measures and to use personal protective
equipment;
• Disconnect all energy sources before starting to connect your
Antamatic® to the power mains;
• Keep the work area clean;
• Carry out installation in good lighting and in favourable environmental
conditions;
• Keep children and/or pets away from the work area;
• Do not install when under the influence of alcohol, drugs and/or
medicines;
• Install the Antamatic® system only on structures with adequate solidity
and straightness;
• The anchorage system (dowels, screws and brackets) to the supporting
structure must be suitable for the purpose and is the responsibility of the
installer. Sir S.r.l. disclaims all liability for incorrect installation.
Power supply voltage 230V AC
Motor supply voltage 24V DC
Power consumption 25W
No-load absorption 0,3A
Absorption at load 1A
Maximum torque 0,9Nm
Reduction ratio 1/13
Rotation speed 160 rpm
Opening speed up to 0,3 m/s
Operating temperature -10/+60°C
Maximum load 80Kg total
Photocell and presence detector input
Technical data
Maximum gap (door width) Overall weight Maximum height
1200mm 80Kg dragged weight 3000mm
Range of use
Intended use
The OPEN 2.0 automation allows motorizing interior single-leaf pedestrian sliding doors, for residential use.
This type of automation, with Low Energy operation, can be installed in environments where the door is used by disabled or elderly
people, or people with limited mobility, after carrying out a risk analysis and considering that the risk for this type of user is low.
To Next Page
Loading...