Sealey MS062 - User Manual

To Next Page

ITEM

NO.

DESCRIPTION ITEM

NO.

DESCRIPTION

1 Large Drift 6 17mm Collet

2 Small Drift 7 19mm Collet

3 10mm Collet 8 20mm Collet

4 12mm Collet 9 25mm Collet

5 15mm Collet

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

MS062 Issue: 2(HF) - 10/05/18

Original Language Version

Refer to instruction

manual

Wear eye

protection

Wear protective

gloves

MOTORCYCLE WHEEL BEARING REMOVAL KIT

9pc

MODEL NO: MS062

1. SAFETY

 WARNING! Ensure Health & Safety, local authority and general workshop practice requirements are adhered to when using this

equipment.

 WARNING! Always refer to the motorcycle manufacturer’s service instructions, or a proprietary manual to establish the

current procedure for removing motorcycle wheels.

 Ensure that the motorcycle wheel and hub are in good condition.

 Use the wheel bearing removal kit in a suitable work area. Keep the area clean and tidy and ensure there is adequate

lighting.

 Keep children and unauthorised persons away from the work area.

 Keep hands clear of the drift and hammer when using the wheel bearing removal kit.

 Wear appropriate personal protective equipment when using the wheel bearing removal kit. A full range of PPE is available from your

Sealey stockist.

 DO NOT use the wheel bearing removal kit for any purpose other than for which it is designed.

 DO NOT use the wheel bearing removal kit if any part of it is damaged or missing.

 DO NOT allow untrained persons to use the wheel bearing removal kit.

 DO NOT attempt to remove a motorcycle wheel bearing when you are tired or under the influence of alcohol, drugs or intoxicating

medication.

 When not in use, clean the wheel bearing removal kit and store in a safe, dry, childproof area.

  WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that

may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must

be applied by the operator.

2. INTRODUCTIONUCT

For easy removal of wheel bearings. Simply choose the correct size collet for the bearing and hammer one of the drifts into the allocated slot.

Covers sizes from 10-25mm so will suit most popular motorcycles and ATV/Quad Bikes.

3. CONTENTSU

Other manuals for Sealey MS062

Instructions2 pages

Need help?

Do you have a question about the Sealey MS062 and is the answer not in the manual?

Summary

Safety Precautions

General Safety and Workshop Practices

Adherence to health, safety, local authority, and workshop practice requirements is mandatory.

Motorcycle Specific Procedures

Always follow the motorcycle manufacturer's service instructions or a proprietary manual for wheel removal.

Work Area and Equipment Condition

Ensure wheel/hub are in good condition, work in a clean, tidy, well-lit area. Keep children away.

Personal Protective Equipment (PPE)

Wear appropriate PPE. Keep hands clear of drifts and hammers during use.

Proper Usage and Maintenance

Do not use if damaged or missing parts. Do not allow untrained persons to use the kit.

Operator Fitness and Storage

Do not use when tired or under the influence. Store kit safely when not in use.

Introduction and Contents

Product Introduction

Designed for easy removal of motorcycle wheel bearings, covering sizes 10-25mm.

Operation Guide

Prepare Wheel Bearing for Removal

Remove wheel per manufacturer's instructions, including retaining circlip and hub bearing seal.

Insert Collet

Select correct collet size, insert into bearing, and place wheel on a firm surface.

Insert Drift into Collet

Locate drift into collet slot and strike with a hammer to expand and bind the collet.

Remove Wheel Bearing

Strike drift to drive bearing and collet out of hub. Grip drift in vice to separate components.

Summary

Safety Precautions

General Safety and Workshop Practices

Adherence to health, safety, local authority, and workshop practice requirements is mandatory.

Motorcycle Specific Procedures

Always follow the motorcycle manufacturer's service instructions or a proprietary manual for wheel removal.

Work Area and Equipment Condition

Ensure wheel/hub are in good condition, work in a clean, tidy, well-lit area. Keep children away.

Personal Protective Equipment (PPE)

Wear appropriate PPE. Keep hands clear of drifts and hammers during use.

Proper Usage and Maintenance

Do not use if damaged or missing parts. Do not allow untrained persons to use the kit.

Operator Fitness and Storage

Do not use when tired or under the influence. Store kit safely when not in use.

Introduction and Contents

Product Introduction

Designed for easy removal of motorcycle wheel bearings, covering sizes 10-25mm.

Operation Guide

Prepare Wheel Bearing for Removal

Remove wheel per manufacturer's instructions, including retaining circlip and hub bearing seal.

Insert Collet

Select correct collet size, insert into bearing, and place wheel on a firm surface.

Insert Drift into Collet

Locate drift into collet slot and strike with a hammer to expand and bind the collet.

Remove Wheel Bearing

Strike drift to drive bearing and collet out of hub. Grip drift in vice to separate components.

The Sealey Motorcycle Wheel Bearing Removal Kit, Model No: MS062, is a specialized tool designed for the easy and efficient removal of wheel bearings from motorcycles, ATVs, and Quad Bikes. This kit covers a range of bearing sizes from 10mm to 25mm, making it suitable for most popular models.

Function Description:

The primary function of the MS062 kit is to facilitate the removal of wheel bearings without causing damage to the wheel, hub, or other surrounding components. It operates by utilizing a system of collets and drifts. A correctly sized collet is inserted into the center of the wheel bearing. A tapered drift is then hammered into a designated slot in the collet, which expands the collet and binds it firmly to the inner race of the wheel bearing. Once the collet is securely bound, the drift is struck again with a hammer to drive the bearing and collet out of the hub. This method ensures a secure grip on the bearing, allowing for controlled and safe extraction.

Important Technical Specifications:

Model Number: MS062
Bearing Size Coverage: 10mm to 25mm
Components:
- Large Drift (x1)
- Small Drift (x1)
- Collets (x7): 10mm, 12mm, 15mm, 17mm, 19mm, 20mm, 25mm
Material: Not explicitly stated, but implied to be durable for hammering and bearing extraction.
Application: Motorcycles, ATVs, Quad Bikes.

Usage Features:

The kit emphasizes safe and correct usage, providing detailed instructions for operation.

Preparation: Before using the kit, users must remove the motorcycle wheel according to the manufacturer's service instructions. If present, retaining circlips and hub bearing seals must also be removed. It is recommended to replace the hub bearing seal with a new item after removal.
Collet Insertion: The first step involves selecting the closest fitting collet and inserting it into the center of the wheel bearing. The wheel is then placed on a firm, solid surface with the collet lowermost, ensuring the allocated slot in the collet is visible through the hub.
Drift Insertion: The tapered end of the appropriate drift (large or small, depending on the bearing size and collet) is located into the allocated slot in the collet. A hammer is used to firmly strike the drift, expanding the collet and binding it to the inner race of the wheel bearing.
Bearing Removal: The wheel and hub must be adequately supported to provide sufficient clearance for the bearing and collet to be driven out, and to prevent damage to brake discs, the hub, or the wheel rim. The drift is then struck with a hammer to remove the wheel bearing and collet from the hub.
Disassembly: After extraction, the drift, wheel bearing, and collet are separated. The drift can be gripped in a vice to facilitate careful detachment of the wheel bearing and collet using a hammer.
Safety Precautions: The manual highlights several critical safety warnings:
- Adherence to Health & Safety, local authority, and general workshop practice requirements.
- Always refer to motorcycle manufacturer's service instructions.
- Ensure the motorcycle wheel and hub are in good condition.
- Use the kit in a suitable, clean, tidy, and well-lit work area.
- Keep children and unauthorized persons away.
- Keep hands clear of the drift and hammer during use.
- Wear appropriate personal protective equipment (PPE), including eye protection and protective gloves.
- DO NOT use the kit for purposes other than its design.
- DO NOT use the kit if any part is damaged or missing.
- DO NOT allow untrained persons to use the kit.
- DO NOT attempt bearing removal while tired or under the influence of alcohol, drugs, or intoxicating medication.
- The warnings and instructions provided cannot cover all possible conditions, emphasizing the need for common sense and caution from the operator.

Maintenance Features:

Cleaning: When not in use, the wheel bearing removal kit should be cleaned.
Storage: The kit should be stored in a safe, dry, childproof area, preferably in its original case, to protect the components and ensure longevity.
Environmental Protection: Users are advised to recycle unwanted materials, tools, accessories, and packaging responsibly. When the product becomes unserviceable, it should be disposed of in an environmentally compatible manner, including draining any fluids into approved containers if applicable.
Warranty: The product comes with a 12-month guarantee from the purchase date, requiring proof of purchase for any claim.
Parts Support: Sealey provides parts support for this product, with contact information for email and telephone inquiries.
Product Improvement: Sealey reserves the right to alter data, specifications, and component parts without prior notice, as part of their policy to continually improve products.