Sealey TJ150E - User Manual

INSTRUCTIONS FOR:
FLOOR TRANSMISSION
JACK 150kg
Model No. TJ150E
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
 Maintain the jack in good condition (use an authorised service agent).
 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
 Locate the jack in a suitable work area. Keep area clean and tidy and free from unrelated materials and ensure that there is adequate
lighting. Also ensure that the floor is level and strong enough (preferably concrete) to take the weight of the jack and the
transmission unit. DO NOT operate the jack on tarmacadam, as the surface may be unstable.
 Keep the jack clean for best and safest performance.
 The maximum transmission unit weight is 150kg. DO NOT exceed this rated capacity.
 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
 Keep hands and fingers clear of the scissor mechanism during use.
 Maintain correct balance and footing, DO NOT over reach. Ensure that the floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the work area.
 DO NOT use the jack for a task it is not designed to perform.
 DO NOT use the jack as a vehicle lifting device.
 DO NOT operate the jack if damaged.
 DO NOT operate the jack when you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT allow untrained persons to operate the jack.
 DO NOT make any modifications to the jack.
 Before storing, ensure that all parts are clean and the jack is fully lowered. Store jack in a safe, dry, childproof area.
 WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and
situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
3. OPERATING INSTRUCTIONS
Model No: .................................................TJ150E
Capacity: ..................................................... 150kg
Minimum Saddle Height:........................... 195mm
Maximum Saddle Height:.......................... 585mm
Base Dimensions: ........................... 400 x 420mm
Ratchet Drive Socket Size: .................. ½" Square
● Suitableforraisingandloweringgearboxanddifferentialunits.
● Easytooperatescissormechanismforprecisionwhenfittingthetransmissionunit.
● Thesaddleisfittedwithawebbingstrapwithmetalrollerbuckletoholdtheloadsecurelyandhasa5°tiltadjustment.
● Fourheavy-dutycastorsprovideflexibilityofmovementwithintheworkplace.
Refer to g.2.
3.1. Ensure that the vehicle being worked on is securely immobilised. If any wheels are removed it MUST be supported securely on
axle stands. NEVER WORK UNDER A VEHICLE SUPPORTED BY A JACK ONLY.
3.2. Unfasten the webbing strap and roll the jack to immediately below the unit to be removed.
3.3. Using a ½" ratchet drive inserted into the drive socket, raise the saddle into light contact with the load.
DO NOT use an impact wrench with this product.
3.4 Thesaddlemaybetiltedbyupto5°toallowbetterregistrationwiththetransmissionunitbeingremoved. Slacken the wingnuts on
both sides to allow adjustment of the saddle and re-tighten to lock in position. DO NOT attempt to adjust tilt whilst under load.
g.1
Original Language Version
© Jack Sealey Ltd© Jack Sealey Ltd
TJ150E Issue: 1 13/12/12

Summary

Safety Instructions

General Safety and Maintenance

Maintain jack condition, use genuine parts, keep clean, and ensure proper repairs for safe performance.

Work Area and Environmental Safety

Ensure a clean, tidy, level, and strong work area. Keep children and unauthorised persons away.

Operator Safety and Personal Precautions

Wear suitable clothing and non-slip shoes. Avoid fatigue, alcohol, drugs, and untrained operation.

Usage Restrictions and Warnings

Do not exceed capacity, misuse, operate if damaged, or make modifications. Store safely.

Important Safety Disclaimer

Manual warnings cannot cover all situations; operator must use common sense and caution.

Introduction and Specification

Product Features Overview

Details scissor mechanism, webbing strap, tilt adjustment, and heavy-duty castors for flexibility.

Technical Specifications

Lists model number, capacity, minimum/maximum saddle height, base dimensions, and drive socket size.

Operating Instructions

Vehicle Immobilisation and Jack Positioning

Secure vehicle with axle stands. Position jack under the unit to be removed.

Raising and Tilting the Load

Use ratchet to raise saddle into contact; adjust tilt up to 5° for better registration.

Securing and Removing Load

Secure unit with webbing strap, remove fastenings, and gently manoeuvre jack to withdraw.

Lowering Load and Re-installation

Reverse ratchet to lower saddle when unit is free. Re-installation is the reverse procedure.

Maintenance

Lubrication of Moving Parts

Periodically apply good-quality grease to all moving parts, especially the lead screw.

Securing Strap Maintenance

Replace the securing strap immediately if it becomes torn or damaged.

Sealey TJ150E Specifications

General

Brand	Sealey
Model	TJ150E
Category	Jacks
Language	English