Seca 515 - User Manual

Questions and Answers

J
Jay CaldwellSep 23, 2025
Why is a seca patient file shown as “not assigned” in the seca 115 PC software following import from a USB memory stick on Seca 515 Measuring Instruments?
- M
  Michelle KennedySep 23, 2025
  If a seca patient file is shown as “not assigned” in the seca 115 PC software after import from a USB memory stick, it could be due to the USB PIN of the USB memory stick used for access to the seca patient database. Manually assign the current seca patient file to an attending physician in seca 115. To import other patient files, use the user PIN to access the seca patient database of the USB memory stick.
M
Melissa CollinsAug 23, 2025
What to do if the touchscreen display stays dark on Seca 515 Measuring Instruments?
- J
  Jared RojasAug 23, 2025
  If the touchscreen display on your Seca Measuring Instruments remains dark, it could be due to several reasons: * The device might be on standby. Try touching the touchscreen display, pressing the on/off button, or placing a load on the device. * The device may not be switched on; ensure the device is powered on. * There might be no power supply; verify that the device is receiving power. * The touchscreen display could be faulty.
K
Karen HerreraAug 25, 2025
Why are results reports not being printed from my Seca Measuring Instruments?
- S
  stacybarryAug 26, 2025
  If results reports are not printing from your Seca Measuring Instruments, it could be due to a few reasons: * The PC printer may not be switched on. Ensure the printer is powered on. * The PC on which the seca 115 PC software is installed might not be switched on. Make sure the PC is turned on. * There may be no network connection established between the device and the seca 115 PC software.
L
Lynn SmithAug 26, 2025
What does ER11 message mean on Seca 515?
- T
  Travis DorseyAug 27, 2025
  The ER11 message on your Seca Measuring Instruments indicates that the device is either overloaded as a whole or in one corner. To resolve this, remove the load or distribute it evenly, and then restart the device.
D
davidgrayAug 27, 2025
What does ER12 message mean on Seca 515 Measuring Instruments?
- A
  Amanda RodriguezAug 27, 2025
  The ER12 message on Seca Measuring Instruments means that the device was switched on with too heavy a load. To fix this, remove the load from the device and restart it.
L
lindseybakerSep 16, 2025
Why is bia tab activated, but module selection does not appear on Seca Measuring Instruments?
- L
  Lindsey LopezSep 16, 2025
  If the bia tab is activated but the module selection does not appear on your Seca Measuring Instruments, it is possible that the module selection has been deactivated. Check the setting and change it if necessary.
C
Christian JonesSep 13, 2025
Why no waist circumference can be entered following bioimpedance measurement on Seca 515 Measuring Instruments?
- A
  Antonio MillerSep 13, 2025
  If you cannot enter waist circumference following a bioimpedance measurement on your Seca Measuring Instruments, the Health risk evaluation module may be deactivated. If the module is not required, continue and complete the measurement. If it is required, activate the evaluation module.
D
Dr. Tiffany BaileySep 14, 2025
Why no PAL value can be entered after bioimpedance measurement on Seca Measuring Instruments?
- D
  debbiejordanSep 14, 2025
  If you cannot enter a PAL value after a bioimpedance measurement on your Seca Measuring Instruments, the Energy evaluation module might be deactivated. If the Energy evaluation module is not required, proceed and complete the measurement. If the Energy evaluation module is required, activate it.
J
Jonathan LewisSep 5, 2025
Why do results of bioimpedance measurement deviate significantly from expected results in Seca 515?
- P
  Paul FisherSep 5, 2025
  Deviations in bioimpedance measurement results on Seca Measuring Instruments can occur if: * The patient moved during the measurement. Ensure the patient remains still and repeat the measurement. * The patient used different pairs of hand electrodes on the left and right. Make sure the patient uses the same hand electrodes on both sides and repeat the measurement.
W
William CowanSep 3, 2025
What does ER16 message mean on Seca 515 Measuring Instruments?
- J
  john56Sep 3, 2025
  The ER16 message on Seca Measuring Instruments indicates that natural vibration has been induced in the device, and the zero point could not be determined. To solve this, restart the device and then restart the measurement.