Why doesn't '0.0' appear before weighing on my Seca Measuring Instruments?
If your Seca Measuring Instruments does not show '0.0' before weighing, it means a load was already on the device when it was switched on. Remove the load from the measuring station and then switch the measuring station off and on again.
Why does my Seca Measuring Instruments display 'bAtt'?
If your Seca Measuring Instruments displays 'bAtt', it indicates that the batteries have discharged. You should replace the batteries to resolve this issue.
How to fix no weight display on Seca Measuring Instruments?
If your Seca Measuring Instruments are not displaying any weight when a load is applied, it could be due to a lack of power. Here's what you can do: * Ensure the measuring station is switched on. * If using batteries, make sure they are properly inserted. * If using a power supply, check that the plug-in power supply unit is correctly connected.
What does 'Er:[No.]:12' mean on Seca Measuring Instruments?
If your Seca Measuring Instruments displays 'Er:[No.]:12', it means the device was switched on with too high a load. Remove the load from the measuring station, then switch the measuring station off and on again.
Why is the weight display flashing on my Seca Measuring Instruments?
If the weight display on your Seca Measuring Instruments is flashing, it means a consistent weight value hasn't been detected yet. This can happen if Hold, Autohold, or Tare functions are active. Wait until the measuring station detects a consistent weight value and the display unit stops flashing. Alternatively, remove the load, wait for '0.0' to display, and then weigh again.
Why can I only see the SYS menu item in the rF menu of my Seca Measuring Instruments?
If, in the rF menu, only the SYS menu item is visible on your Seca Measuring Instruments, it means the WiFi function is deactivated. Activate the WiFi function.
Why is Workflow LED not working on Seca 797 Measuring Instruments?
If you are using Seca 797 and the Workflow LED does not come on, it indicates that the WiFi function is deactivated. Activate the WiFi function.
What if Workflow LED is defective on Seca Measuring Instruments?
If the Workflow LED does not come on for your Seca Measuring Instruments, it could be that the Workflow LED is defective. Contact your administrator or hospital technician, or inform Seca Service.
What does 'Er:[No.]:16' mean on Seca Measuring Instruments?
If your Seca Measuring Instruments displays 'Er:[No.]:16', it means the device was caused to oscillate, and the zero point could not be determined. Switch the measuring station off, then switch it back on again.
What does 'Er:8:95' mean on Seca Measuring Instruments?
If your Seca Measuring Instruments is displaying 'Er:8:95', it indicates a hardware fault. Contact your administrator or hospital technician, or inform Seca Service.
Explains the meaning of DANGER, WARNING, CAUTION, and NOTICE used in the manual for hazard identification.
Covers essential safety measures for handling the device, including explosion risks and patient hazards.
Provides crucial warnings and guidelines to prevent electric shock hazards during device operation and setup.
Details measures to prevent patient injuries, falls, and potential infections during use.
Outlines safety steps to prevent patients from slipping on the weighing platform.
Advises on hygiene practices to minimize infection risks during measurements.
Offers guidance on avoiding device damage from liquids, impacts, temperature, or improper handling.
Details safety precautions for handling batteries, including risks of explosion and damage.
Lists components to be disinfected before initial use.
Details on inserting batteries and connecting the power supply unit.
Step-by-step guide for connecting the external power adapter.
Guides the user through the process of weighing a patient, including safety precautions.
Details the procedure for measuring patient height, including safety advice.
Instructions for measuring height for patients under 1.22m and entering the value.
Describes the digital measurement of height for patients over 1.22m.
Explains how to calculate and display the Body Mass Index (BMI) from weight and height.
Details scanning patient/user IDs and transmitting data wirelessly using WiFi and EMR integration.
Details the process for disinfecting the device with alcohol-based disinfectants.
Lists common problems, their causes, and remedies for general device malfunctions.
Addresses issues related to data transmission errors and the workflow LED status.
General| Graduation | 100 g |
|---|---|
| Display | LCD |
| Type | Electronic Scale |
| Capacity | 300 kg |
| Functions | TARE, Hold, BMI, Auto Power Off |
| Power Supply | Batteries |
To Next Page
