Seca 787 - User Manual

Questions and Answers

P
poolepeggyAug 21, 2025
What to do if 'StOP' is displayed on Seca Measuring Instruments?
- K
  Kelsey PachecoAug 21, 2025
  If your Seca Measuring Instruments display shows 'StOP', it means the maximum capacity of the device has been exceeded. To resolve this, remove some of the load from the measuring station.
B
Beth LangSep 4, 2025
What does 'Er:8:95' mean on Seca Measuring Instruments?
- M
  Morgan YoungSep 4, 2025
  If your Seca Measuring Instruments is displaying 'Er:8:95', it indicates a hardware fault. Contact your administrator or hospital technician, or inform Seca Service.
R
Robert LiSep 2, 2025
What does 'Er:8:94' mean on Seca Measuring Instruments?
- E
  Erin EllisonSep 2, 2025
  If your Seca Measuring Instruments displays an error message 'Er:8:94', it indicates that an error occurred during the measurement procedure because IDs were scanned at the wrong time. Cancel the measurement procedure and repeat it, making sure to follow the proper sequence. If the issue persists, contact your administrator or hospital technician.
M
mrodriguezSep 1, 2025
What does 'Id:Er' mean on Seca Measuring Instruments?
- N
  Nicole ReyesSep 1, 2025
  If your Seca Measuring Instruments displays 'Id:Er', it means that the ID of the user or patient has not been found in the EMR system. Try rescanning the ID. If the problem continues, contact your administrator or hospital technician.
S
Shannon MathisAug 30, 2025
What does 'Er:[No.]:32' mean on Seca Measuring Instruments?
- B
  brooksericAug 30, 2025
  If your Seca Measuring Instruments displays the message 'Er:[No.]:32', it indicates that an internal communication error has occurred. Try switching the measuring station off and then on again. Also, ensure that the display cable is connected correctly (for seca 797 models). If the problem persists, contact Seca Service.
M
Meredith GibsonAug 29, 2025
What does 'Er:[No.]:11' mean on Seca Measuring Instruments?
- J
  jodicrawfordAug 29, 2025
  If your Seca Measuring Instruments displays the message 'Er:[No.]:11', this indicates that the device has too high a load or too much load in one corner. Remove the load or distribute the weight more evenly. Then, switch the measuring station off and on again. If the problem continues, contact Seca Service.
J
John SimonAug 27, 2025
Why is the weight display flashing on my Seca Measuring Instruments?
- T
  Taylor KnappAug 27, 2025
  If the weight display on your Seca Measuring Instruments is flashing, it means a consistent weight value hasn't been detected yet. This can happen if Hold, Autohold, or Tare functions are active. Wait until the measuring station detects a consistent weight value and the display unit stops flashing. Alternatively, remove the load, wait for '0.0' to display, and then weigh again.
P
Phillip CoxAug 27, 2025
What does 'Er:[No.]:12' mean on Seca Measuring Instruments?
- K
  Kenneth VazquezAug 27, 2025
  If your Seca Measuring Instruments displays 'Er:[No.]:12', it means the device was switched on with too high a load. Remove the load from the measuring station, then switch the measuring station off and on again.
D
David PorterAug 25, 2025
How to fix no weight display on Seca Measuring Instruments?
- J
  Joseph WebbAug 25, 2025
  If your Seca Measuring Instruments are not displaying any weight when a load is applied, it could be due to a lack of power. Here's what you can do: * Ensure the measuring station is switched on. * If using batteries, make sure they are properly inserted. * If using a power supply, check that the plug-in power supply unit is correctly connected.
S
Scott ReyesAug 23, 2025
Why does my Seca Measuring Instruments display 'bAtt'?
- D
  Denise BellAug 23, 2025
  If your Seca Measuring Instruments displays 'bAtt', it indicates that the batteries have discharged. You should replace the batteries to resolve this issue.