Seiko S149 - Accumulated Elapsed Time Measurement; Lap and Split Time Measurement; Lap Time Progress Display

Whenthegripswitchisused:
① Changeovertothegripswitch
● Connectthegripswitchtothestopwatch.
② Timemeasurement
● The measurement is started by pressing the grip switch
once.Splittimeandlaptimecanbemeasuredrepeatedly
witheachpressofthegripswitch.
Gripswitch
● Slideupthegripswitchselectorlocatedontherightsideofthe
stopwatch.
EXT
▲
＊Whilethegripswitchselectoris setatthe
upperposition,button○
Ａ
and○
B
willnotwork,
andthestopwatchisoperatedsolelyby the
gripswitch.
＊By pressing thegripswitch, split time andlaptime can be measured,butthe
measurementcannot be stopped. Afterthefinal split or laptime is measured,
followthestopsin④ Endofmeasurement"tostopthemeasurement.
③Printoutoflapseoftime(Onlywheninthe
time/calendar modeand the power switch of the
printerison)
●Thestopwatchcanprintoutthetimealaptimeismeasured
inthesamemanner as you press the grip switch in the
stopwatchmode.
（Start）→（With eachpressofthegrip
switch,splittimeandlaptime
aremeasuredrepeatedly.）
c
Upperposition
Howtousethelocklever
④Endofmeasurement
● Afterthemeasurementisover,slidedownthegripswitch
selector.
●Afterslidingdowntheselector,pressbutton○
Ａ
tostopthe
measurementandthenpressbutton○
Ｂ
toresetthe
stopwatch.
EXT
▲
d
Lowerposition
SPLIT
RECALL
BLOCK
LAP
STOP
BATT.
LAP
LAP／SPLIT
RESET
START
STOP
F
E
(Stop)
○
Ａ
\
SPLIT
RECALL
BLOCK
LAP
STOP
BATT.
LAP
LAP／SPLIT
RESET
START
STOP
F
E
(Resetto"00")
○
Ｂ
\
Topreventanymistakenoperationofbutton○
Ａ
(start/stop
of the stopwatch) during the measurement, it is
recommendedthatbutton○
Ａ
belockedwiththelocklever
afterthemeasurementisstarted.
BLOCK
F
E
SYSTEM STOPWATCH
300LAP／SPLIT MEMORY
LOCK
LAP／SPLIT
RESET
START
STOP
CLEAR
1/100 STOP.W A/S SET TIME
RECALL
Locklever
Afterthemeasurementisstarted,
slidedownthelocklever.
＊While the lock lever is slid down,
button○
Ａ
(START/STOP)islocked
andcannotbepressed.
STOP-W.A/SSETTIME
５.HOWTOUSETHEMEMORYFUNCTION
RECALL
BLOCK
STOP
BATT.
LAP
F
E
300LAP／SPLIT MEMORY
LOCK
LAP／SPLIT
RESET
START
STOP
CLEAR
1/100 STOP.W A/S SET TIME
RECALL
Button○
Ａ
Button○
Ｂ
STOP-W.A/SSETTIME
Recallbutton（Memoryrecallbutton）
■Thememoryrecallfunction
・Thedataobtainedinthemeasurementcanberecalledanddisplayed.
・Upto100blocksofdataor300datacanbestoredandrecalled.
・Besidesbeingrecalled and displayed, the datain memory can also beprinted out.
(Referto"6.HOWTOPRINTOUT")
・Thestoreddataisrecalledbypressingrecallbutton.Thedataisrecalledsuccessively
ifthebuttoniskeptpressed.
・Thestoreddatacanberecalledwhilethestopwatchismeasuring.
・Thedatacanbestoredinmemoryevenwhileprintingoutthedataduringthe
measurement.
・Orderofrecallingthestoreddata

Whenthestopwatchisstopped
Whenthestopwatchisinuse
Witheachpressofrecallbutton
Thedataisrecalledstartingfromtheoldestone.
Thedataisrecalledstartingfromthenewestone.
・Buttonoperationwhilethestoreddataisrecalled
Displaybeforerecall
Reset
Stopped
Measuring
Button○
Ａ
 Button○
Ｂ


Clearingthedatain
memory
Returningtothedisplay
beforerecall
Measuringlap/splittime


Returningtothe
displaybeforerecall
Returningtothe
displaybeforerecall
Returningtothe
displaybeforerecall
Returningtothe
displaybeforerecall
Returningtothe
displaybeforerecall
Stoppingthe
measurement
modeselection
button①(STOP.W)