Need help?Do you have a question about the Senco FramePro 651 and is the answer not in the manual?
Must read and understand the 'SAFETY INSTRUCTIONS' manual before using the tool.
Always point the tool away from yourself and others, and connect air to the tool.
Never use a tool that has air leaks or requires repair.
Install the Nail Guide (GC0631) for nails shorter than 2 1/2 inches.
Insert nails into magazine, use genuine SENCO fasteners, do not load with safety or trigger depressed.
Nails can be driven two ways: 'Trigger Fire' or 'bottom-fire' mode.
Nails can only be driven one way: depress safety element, then pull trigger.
Read the CSSR for safety information regarding Dual Action and Restrictive triggers.
Position Nail Guide, insert nails, use SENCO fasteners, do not load with safety or trigger depressed.
Activate tool by positioning nail, depressing tool against surface, and pulling trigger.
Adjust fastener depth by using a wrench or screwdriver, disconnect air supply first.
Adjust FramePro XP depth using the wheel, disconnect air supply first.
Disconnect air, release feeder shoe, remove fasteners, slide magazine back.
Release E-Z Clear latch to open the door for clearing jams.
Remove jammed fastener, close door and latch, then clear guide body.
Loosen knob, pull magazine back, slide back into position, tighten knob.
Connect air supply, replace fasteners, and pull feeder shoe back.
Convert tool for flat surface applications by adding the no-mar pad.
Rotate deflector to change exhaust air direction; disconnect air supply first.
Tool prevents activation with 6 or fewer nails or when magazine is not locked.
Read and understand the 'SAFETY INSTRUCTIONS' manual before using the tool.
Keep all screws tight to ensure safe operation and prevent part breakage.
Inspect safety element and trigger for free movement when tool is disconnected.
Apply Senco pneumatic oil to air inlet twice daily; use only recommended oil.
Wipe tool clean daily and inspect for wear; use non-flammable cleaning solutions cautiously.
Troubleshoot air leaks near top or sluggish operation by checking supply and tightening screws.
Address air leaks near bottom or poor return by cleaning tool or tightening screws.
Fix air leaks near top or sluggish operation by tightening screws or installing a repair kit.
Resolve air leaks near bottom or poor return by cleaning the tool or tightening screws.
For other FramePro problems, contact SENCO for assistance.
Specifications for SN70 JF and GE nail codes, including length in inches and mm.
Specifications for SN70 GC, HC, HF, KC nail codes, including length and diameter.
Specifications for FramePro 602/702XP FRH nail codes (GL, GD, HD, HL, KD, D).
Specifications for FramePro 652/752XP FRH nail codes, including length and diameter.
Specifications for FramePro 601/701XP CH nail codes (GE, GC, HC, HE, H, KC, C).
Specifications for FramePro 651/751XP CH nail codes, including length and diameter.
Specifications for SN60MC KJ, MD, NN staple codes, including length and diameter.
Summary of technical specifications for SN70 and SN60MC tools, including pressure, consumption, and weight.
Technical specifications for FramePro 601, 701XP, and 721 models.
Technical specifications for FramePro 602/702XP FRH series models.
Technical specifications for FramePro 651/751XP CH series models.
Technical specifications for FramePro 752XP FRH series models.
Feature helpful for precise fastener placement.
Durable carrying case to protect tool and accessories.
Modify cap to attach a hanger using a tap and eyebolt.
Full line of accessories including air compressors, hoses, fittings, and safety gear.
Warranty periods for Pneumatic, Duraspin, Fusion, Combo Kit, and GasTools.
Requires dated sales receipt, warranty registration, and return to authorized center.
Excludes normal wear parts, misuse, accidents; requires proper air pressure and maintenance.
SENCO replaces tools destroyed by Acts of God if registered and documented.
Must read and understand the 'SAFETY INSTRUCTIONS' manual before using the tool.
Always point the tool away from yourself and others, and connect air to the tool.
Never use a tool that has air leaks or requires repair.
Install the Nail Guide (GC0631) for nails shorter than 2 1/2 inches.
Insert nails into magazine, use genuine SENCO fasteners, do not load with safety or trigger depressed.
Nails can be driven two ways: 'Trigger Fire' or 'bottom-fire' mode.
Nails can only be driven one way: depress safety element, then pull trigger.
Read the CSSR for safety information regarding Dual Action and Restrictive triggers.
Position Nail Guide, insert nails, use SENCO fasteners, do not load with safety or trigger depressed.
Activate tool by positioning nail, depressing tool against surface, and pulling trigger.
Adjust fastener depth by using a wrench or screwdriver, disconnect air supply first.
Adjust FramePro XP depth using the wheel, disconnect air supply first.
Disconnect air, release feeder shoe, remove fasteners, slide magazine back.
Release E-Z Clear latch to open the door for clearing jams.
Remove jammed fastener, close door and latch, then clear guide body.
Loosen knob, pull magazine back, slide back into position, tighten knob.
Connect air supply, replace fasteners, and pull feeder shoe back.
Convert tool for flat surface applications by adding the no-mar pad.
Rotate deflector to change exhaust air direction; disconnect air supply first.
Tool prevents activation with 6 or fewer nails or when magazine is not locked.
Read and understand the 'SAFETY INSTRUCTIONS' manual before using the tool.
Keep all screws tight to ensure safe operation and prevent part breakage.
Inspect safety element and trigger for free movement when tool is disconnected.
Apply Senco pneumatic oil to air inlet twice daily; use only recommended oil.
Wipe tool clean daily and inspect for wear; use non-flammable cleaning solutions cautiously.
Troubleshoot air leaks near top or sluggish operation by checking supply and tightening screws.
Address air leaks near bottom or poor return by cleaning tool or tightening screws.
Fix air leaks near top or sluggish operation by tightening screws or installing a repair kit.
Resolve air leaks near bottom or poor return by cleaning the tool or tightening screws.
For other FramePro problems, contact SENCO for assistance.
Specifications for SN70 JF and GE nail codes, including length in inches and mm.
Specifications for SN70 GC, HC, HF, KC nail codes, including length and diameter.
Specifications for FramePro 602/702XP FRH nail codes (GL, GD, HD, HL, KD, D).
Specifications for FramePro 652/752XP FRH nail codes, including length and diameter.
Specifications for FramePro 601/701XP CH nail codes (GE, GC, HC, HE, H, KC, C).
Specifications for FramePro 651/751XP CH nail codes, including length and diameter.
Specifications for SN60MC KJ, MD, NN staple codes, including length and diameter.
Summary of technical specifications for SN70 and SN60MC tools, including pressure, consumption, and weight.
Technical specifications for FramePro 601, 701XP, and 721 models.
Technical specifications for FramePro 602/702XP FRH series models.
Technical specifications for FramePro 651/751XP CH series models.
Technical specifications for FramePro 752XP FRH series models.
Feature helpful for precise fastener placement.
Durable carrying case to protect tool and accessories.
Modify cap to attach a hanger using a tap and eyebolt.
Full line of accessories including air compressors, hoses, fittings, and safety gear.
Warranty periods for Pneumatic, Duraspin, Fusion, Combo Kit, and GasTools.
Requires dated sales receipt, warranty registration, and return to authorized center.
Excludes normal wear parts, misuse, accidents; requires proper air pressure and maintenance.
SENCO replaces tools destroyed by Acts of God if registered and documented.
General| Type | Framing Nailer |
|---|---|
| Power Source | Pneumatic |
| Operating Pressure | 70-120 PSI |
| Nail Angle | 21 Degrees |
| Fastener Type | Nails |
| Nail Size | 2" to 3-1/2" |
| Nail Gauge | 0.113" to 0.131" |
| Magazine Capacity | 60 |
| Firing Mode | Sequential |
| Length | 12.5 inches |
To Next Page