SetOne Easy One - Antenna & Satellite Setup

Operation
9
z Delete: Use CH+/CH- to choose the channels you want to delete, and push blue button to delete a Satellite
by selecting Yes or No in the screen hints.
● Select: Use CH+/CH- to choose a satellite, press OK to confirm the search.
2.3 Antenna Setup
Press VOL► button or OK button to access this submenu item, and press CH+/- button to choose an option, or
press EXIT/ MENU to quit current operation.
2.3.1 Fixed Antenna
● Satellite: Choose a satellite,
● LNB Freq: Press OK to select a proper LNB Frequency.
● Transponder: Press OK to select a transponder.
● DiSEqC1.0 : Press OK to select a digital control port: Disable/ Port 1/ Port 2…Port 4.
● 22K: Use VOL◄/VOL► button to activate or deactivate 22K Hz switch.
● Polarity: Use VOL◄/VOL► button to choose a polarity voltage mode out of Auto, H(horizontal) and
V(vertical).
2.3.2 Motor Antenna
z LNB Type: Press OK to choose the LNB Frequency.
z Motor Type: Use VOL◄/VOL► button to select either USALS or DisEqC 1.2.
z Local Longitude: Use VOL◄/VOL► button to select either E(East) or W(West) before pressing OK to
confirm and numeric buttons to input the longitude needed.（Note: This item can be set only when Motor
Type is set to USALS.）
z Local Latitude: Use VOL◄/VOL► button to select either S(South) or N (North) before pressing OK to
confirm and numeric buttons to input the latitude needed.（Note: This item can be set only when Motor Type is
set to USALS.）
z Delete All: Delete the installation parameters of LNB.
z Motor Setting:
a. Satellite: Press OK to select the satellite to be followed up；
b. Transponder: Choose a transponder on the positioned satellite.
c. Position No. & Save: Press VOL◄/VOL► button to set the Position No. of current satellite or
transponder and save.
d. GO to X: Press OK button to choose the position of a satellite.
e. Save: Use VOL◄/VOL► button to choose “moving east or west, operate with reference to the
signal quality bars, and press OK to save current channel once the signal is good enough.
f. Recalculation: Update the related parameters of automatic positioner.
z Limit Setup:
a. Limit Setup: Press VOL◄/VOL► button to choose any of the Limit mode: Disable/ West Limit/ East
Limit
b. Limit Setup: Press VOL◄/VOL► button long enough to set the offset range of positioning in
particular direction (West or East) following the screen hints.
c. Go to Reference: Go to Reference: Press OK to go back to the Reference position of automatic
positioning.
2.4 Single Satellite Search
z Satellite: Press OK to choose a satellite for search.
z FTA Only: Yes（Search the free channels only）/No （Search both free and paid channels）
z Scan Channel: TV Channel, Radio, and TV + Radio
z Network Search: Yes\No (This operation can be performed only in Preset Scan mode.)
z Scan Mode: Auto Scan/Preset Scan
z Search: Start searching.
2.5 Multi Satellite Search
z Satellite: Press OK to choose satellites for search.
z FTA Only: Yes（Search the free channels only）/No （Search all channels(free and paid)）
z Scan Channel: TV Channel, Radio, and TV + Radio
z Network Search : Yes\No
z Scan Mode: Auto Scan/Preset Scan
z Search: Start search.
2.6 TP List (Transponder List)
Press VOL► button or OK button to access this submenu item. Then press CH+/CH- button to choose an option,
and press OK to start search, or press EXIT/ MENU to quit current operation. As for the operation of Edit/ Add/ Delete/
Search function, please refer to item 2.2 Satellite List for more information.