SEW-Eurodrive DFP21B User Manual

Gearmotors \ Industrial Gear Units \ Drive Electronics \ Drive Automation \ Services
Fieldbus Interface DFP21B
PROFIBUS DP-V1
M anual
FA375100
Edition 07/2006
11479019 / EN

SEW-Eurodrive DFP21B Specifications

General

Brand	SEW-Eurodrive
Model	DFP21B
Category	Recording Equipment
Language	English

Summary

1 Important Notes

1.1 Explanation of symbols

Explains symbols used in the manual for safety and information.

2 Safety Notes

2.2 General safety notes

Presents general safety guidelines for operation and installation.

2.4 Installation / assembly

Directs users to section 4 for installation and assembly instructions.

2.5 Startup / operation

Directs users to section 5 for startup and operation instructions.

3 Introduction

3.1 Content of the manual

Outlines what the manual describes, including installation, usage, and configuration.

3.3 Features

Highlights the capabilities of the DFP21B option for connecting to automation systems.

3.3.5 Configuring the PROFIBUS option card

Details setting fieldbus parameters using hardware switches on the card.

4 Assembly and Installation Notes

4.1 Installing the DFP21B option card in MOVIDRIVE® MDX61B

Instructions for installing the DFP21B option card into the MOVIDRIVE® MDX61B unit.

4.2 Installing the DFP21B option card in MOVITRAC® B

Instructions for installing the DFP21B option card into the MOVITRAC® B unit.

4.8 Setting the PROFIBUS station address

Details how to set the PROFIBUS station address using DIP switches on the option card.

5 Project Planning and Startup

5.2 DP master project planning with MOVIDRIVE® GSD file

Guides on project planning for DP master using MOVIDRIVE® GSD files.

5.4 Setting the MOVIDRIVE® MDX61B drive inverter

Instructions for setting the MOVIDRIVE® MDX61B drive inverter for PROFIBUS control.

5.5 Setting the MOVITRAC® frequency inverter

Instructions for setting the MOVITRAC® frequency inverter for PROFIBUS control.

6 PROFIBUSDP Operating Characteristics

6.1 Controlling the MOVIDRIVE® MDX61B drive inverter

Explains how the drive inverter is controlled via the PROFIBUS process data channel.

6.2 Controlling the MOVITRAC® inverter (gateway)

Describes controlling the MOVITRAC® inverter via the PROFIBUS DP process data channel.

6.3 Parameter settings via PROFIBUS DP

Explains accessing drive parameters via the MOVILINK® parameter channel.

7 PROFIBUSDP-V1 Functions

7.1 Introduction to PROFIBUS DP-V1

Describes functions and terms for SEW drive inverters on PROFIBUS DP-V1.

7.3 Structure of the DP-V1 parameter channel

Details the structure of the DP-V1 parameter channel for drive parameter setting.

8 Operation of MOVITOOLS® MotionStudio via PROFIBUS

8.1 Introduction

Introduces operation of MOVITOOLS® MotionStudio via PROFIBUS DP-V1 for parameter services.

8.5 Configuring SIMATIC NET

Guides on configuring SIMATIC NET for PROFIBUS communication.

8.6 Configuration of SEW communication server

Explains how to configure the SEW communication server for MOVITOOLS®.

9 Error Diagnostics

9.1 Diagnostic Procedures

Demonstrates fault analysis methods for common problems like inverter not working on PROFIBUS.

9.2 List of errors

Provides a list of errors with their designation, response, cause, and measures.

10 Technical Data

10.1 Option DFP21B for MOVIDRIVE® MDX61B

Lists technical specifications for the DFP21B option with MOVIDRIVE® MDX61B.

10.2 DFP21B option for MOVITRAC® B and UOH11B gateway housing

Lists technical specifications for the DFP21B option with MOVITRAC® B and UOH11B gateway.