SEW-Eurodrive X Series Addendum To The Assembly And Operating Instructions

SEW-Eurodrive X Series

24 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

*22860851_0317*

Drive Technology \ Drive Automation \ System Integration \ Services

Addendum to the Assembly and

Operating Instructions

Industrial Gear Units

X.. Series Helical and Bevel-Helical Gear Units

Oil-Water Cooler for Splash or Bath Lubrication /OWC

Edition 03/2017 22860851/EN

Table of Contents

Other manuals for SEW-Eurodrive X Series

Assembly And Operating Instructions380 pages

Assembling And Operating Instructions348 pages

Questions and Answers:

T
tinakeyAug 13, 2025
What to do if there is no oil flow or oil flow is too low in SEW-Eurodrive Industrial Equipment?
- S
  Susan BaileyAug 13, 2025
  If you notice no oil flow or that the oil flow is too low in your SEW-Eurodrive Industrial Equipment, several factors could be at play. First, ensure the rotating direction is correct and properly connected. Also, check that the motor is running as expected. Another possibility is a blocked oil circuit; make sure all stopping valves are open. Finally, high suction pressure could be the culprit; select a suction pipe/hose that is adequately wide and reduce the suction height.
A
Andrew KnoxAug 17, 2025
Why is the operating temperature too high in my SEW-Eurodrive X Series?
- E
  Erica MooreAug 17, 2025
  High operating temperatures in SEW-Eurodrive Industrial Equipment can stem from several causes. It could be due to excessive or old oil, or heavily contaminated oil, requiring you to check the oil level and change the oil if needed, and analyze the oil to determine the cause. High ambient temperatures can also be a factor, so protect the gear unit from external heat. For gear units with a fan, ensure the air intake openings and gear unit housing are clean. If equipped with an oil-air or oil-water cooling system, consult its operating instructions. For units with built-in cooling, verify the cooling liquid flow rate, entry temperature, and clean the cooling system if there are deposits.
C
Carol RodriguezAug 20, 2025
How to troubleshoot unusual, regular running noise in SEW-Eurodrive Industrial Equipment?
- S
  Scott ZimmermanAug 20, 2025
  Unusual, regular running noises in SEW-Eurodrive Industrial Equipment can arise from several issues. A meshing or grinding noise may indicate bearing damage, suggesting a need to check the oil consistency and change the bearings. A knocking noise could point to an irregularity in the gearing, in which case you should consult SEW-EURODRIVE and provide an audio recording. Deformation of the housing upon tightening can also cause noise, requiring you to check the gear unit mounting. Insufficient rigidity of the gear unit foundation may also generate noise, suggesting that you reinforce the foundation.
S
snydermonicaAug 25, 2025
What to do if the temperature at bearing points is too high in SEW-Eurodrive X Series Industrial Equipment?
- D
  dsmithAug 25, 2025
  High temperature at bearing points in SEW-Eurodrive Industrial Equipment can be caused by not enough oil or oil that is too old. In such cases, you should check the oil level and change the oil if necessary. Another potential cause is damaged bearing. If you suspect this, check the bearing and replace it if necessary.
J
Jesse AllenAug 28, 2025
Why is there unusual noise in the area where the SEW-Eurodrive Industrial Equipment gear unit is mounted?
- L
  Lisa BenitezAug 28, 2025
  Unusual noise in the area where the SEW-Eurodrive Industrial Equipment gear unit is mounted could be due to a loosened gear unit mounting. You should tighten the retaining screws and nuts to the specified torque. Also, damaged or defective retaining screws or nuts may be the cause, so replace them if needed.
B
Brett Williams DVMSep 4, 2025
How to fix unusual noise in SEW-Eurodrive DC Drives gear unit mounting?
- M
  Marcus SheltonSep 4, 2025
  If you notice unusual noise coming from the mounting area of your SEW-Eurodrive DC Drives gear unit, it may be due to a loosened gear unit mounting. You should tighten the retaining screws and nuts to the specified torque. If the screws or nuts are damaged, replace them.
E
emcgrathSep 8, 2025
What to do if temperature at bearing points is too high in SEW-Eurodrive DC Drives?
- A
  Alexis CruzSep 8, 2025
  If the temperature at the bearing points of your SEW-Eurodrive DC Drives is too high, it could be due to insufficient or old oil. Check the oil level and correct it if necessary. Also, check when the oil was last changed and replace it if needed. It is also possible that the bearing is damaged.

SEW-Eurodrive X Series Specifications

General

Series	X Series
Gearbox Size	Various sizes available
Output Shaft	Solid shaft, hollow shaft
Lubrication	Oil lubrication
Protection Class	IP65
Ambient Temperature	-20 °C to +40 °C (standard), wider range available
Altitude	Up to 1000 m above sea level (standard)

Related product manuals

MOVIDRIVE MDA90A-0020-503-X-S00

MOVIDRIVE MDA90A-0040-503-X-S00

MOVIDRIVE MDA90A-0240-503-X-S00

MOVIDRIVE MDA90A-0320-503-X-S00

MOVIDRIVE MDA90A-0160-503-X-S00

MOVIDRIVE MDA90A-0480-503-X-S00

MOVIDRIVE MDA90A-1000-503-X-S00

MOVIDRIVE MDA90A-0640-503-X-S00

MOVIDRIVE MDD90A-0040-503-X-S0X

MOVIDRIVE MDD90A-0080-503-X-S00

Preview: MOVIDRIVE MDC90A-0120-50X-X-000

MOVIDRIVE MDC90A-0120-50X-X-000

SEW-Eurodrive R17 DRS71S4