EasyManua.ls Logo

SFA Sanicondens Best Flat - User Manual

SFA Sanicondens Best Flat
16 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
C
US
USA
CDN
IMPORTANT/IMPORTANTE
DO NOT RETURN ANY MERCHANDISE TO THE VENDOR.
NE PAS RETOURNER DE MARCHANDISE AU VENDEUR.
NO REGRESE NINGUNA MERCANCÍA AL VENDEDOR.
For customer Service, Returns or Technical Questions, please call Saniflo’s Technical support toll-free at
800-571-8191 (USA) or 800-363-5874 (CDN).
Pour le service client, les retours ou toute question technique, merci d’appeller le service technique de
Saniflo au numéro suivant : 800-571-8191 (USA) or 800-877-8538 (CDN).
Para el servicio al cliente, devoluciones o preguntas técnicas, por favor llame al soporte técnico de
Saniflo sin cargo al 800-571-8191 (USA)
This product must be installed in strict accordance with local plumbing codes. Product should be installed by a licensed plumber.
Le produit doit être installé dans le respect des règlements sanitaires locaux. Le produit doit être installé par un plombier qualifié.
El producto debe ser instalado en estricto acuerdo con los códigos locales de plomería. El producto debe ser instalado por un
plomero con licencia.
191
02.2021
Sanicondens® Best Flat
The user should retain these instructions for future reference.
À lire attentivement et à conserver à titre d’information.
El usuario debe mantener estas instrucciones para futura referencia.

Questions and Answers

  • A
    alex48Aug 11, 2025
    Why my SFA Sanicondens Best Flat doesn’t start?
    • C
      Christopher CarlsonAug 11, 2025
      If your SFA Water Pump doesn't start, several factors could be the culprit. First, ensure the unit is properly plugged into the power supply. If it is, verify that the lock pin has been removed. Also, make sure the unit is level using a leveling tool. Check your main power to rule out a power outage. A blocked float can also prevent the pump from starting, so clean the tank. Finally, inspect the condensate inlet pipe for blockages and clean it if necessary.
  • J
    Jeffrey JohnsonAug 19, 2025
    What to do if my SFA Water Pump does not lift?
    • H
      Heather SmithAug 19, 2025
      If your SFA Water Pump is not lifting, it could be due to a blocked non-return valve, which requires cleaning. Another possible cause is a blockage in the discharge pipe, so be sure to clean the discharge pipe.
  • J
    Joseph HinesAug 27, 2025
    What to do if my SFA Sanicondens Best Flat Water Pump doesn't start?
    • R
      Ryan DelgadoAug 27, 2025
      If your SFA Water Pump doesn’t start, there are several possible causes: * It might not be properly connected to the power supply. Ensure the unit is plugged in. * The lock pin may not have been removed. Take the lock pin out. * The unit might not be leveled. Use a leveling tool to check and adjust the unit. * There could be a power outage. Check the main power in your house. * The float could be blocked. Clean the tank. * The condensate inlet pipe might be blocked. Clean the inlet pipe.
  • M
    Michael WilliamsSep 2, 2025
    Why SFA Sanicondens Best Flat Water Pump does not lift?
    • K
      Karen MathisSep 2, 2025
      If the SFA Water Pump does not lift, it could be due to a blocked non-return valve. In this case, clean the valve. Alternatively, the discharge pipe might be blocked, so you should clean the discharge pipe.

SFA Sanicondens Best Flat Specifications

General IconGeneral
ModelSanicondens Best Flat
TypeCondensate Pump
Max Flow Rate342 L/h
Max Head4.5 m
Power Supply230 V
Discharge Pipe Diameter8 mm
Voltage230 V
Frequency50 Hz
Maximum Vertical Discharge4.5 m
Protection ClassIP20
ApplicationCondensate Removal
Noise Level≤ 45 dBA
Sound Level≤ 45 dBA
Inlet/Outlet8 mm

Related product manuals