Sharp AL-1556 - User Manual

Questions and Answers

M
Michael ButlerAug 21, 2025
What to do if the error indicator appears on my Sharp AL-1556?
- M
  Michael RossAug 21, 2025
  If your Sharp All in One Printer is showing an error indicator, it could be due to several reasons. A paper misfeed may have occurred, so remove any misfed paper. The cover or the RSPF cover might be open, so ensure they are closed. If the TD cartridge is empty, replace it with a new one. If [L1-00] appears, turn off the power, release the scan head locking switch, and turn the power back on. If none of these resolve the issue, try turning the power off and on again; if the error persists, contact your authorized service representative.
S
Sara DelacruzSep 3, 2025
What does it mean when my Sharp All in One Printer says 'INSTALL A TD CARTRIDGE'?
- B
  bryanramirezSep 3, 2025
  If your Sharp All in One Printer displays 'INSTALL A TD CARTRIDGE', it indicates that the TD cartridge is not installed correctly. Reinstall the TD cartridge to resolve this issue.
A
Alicia RodriguezSep 1, 2025
Why is my Sharp AL-1556 producing blank copies?
- R
  Randall RobinsonSep 1, 2025
  If your Sharp All in One Printer is producing blank copies, ensure the original document is placed correctly. Place the original face up in the RSPF or face down on the document glass.
M
Michelle CisnerosAug 30, 2025
Why are copies from my Sharp AL-1556 smudged or dirty?
- H
  henrykellyAug 31, 2025
  If copies from your Sharp All in One Printer are smudged or dirty, the document glass or the underside of the RSPF may be dirty. Clean these components regularly. Also, ensure you are using a clean original document.
H
Heather SchultzAug 29, 2025
What to do if my Sharp AL-1556 says 'LOAD XX PAPER INTO TRAY'?
- T
  Teresa JeffersonAug 29, 2025
  If your Sharp All in One Printer displays 'LOAD XX PAPER INTO TRAY', it means the paper size setting doesn't match the paper loaded in the tray. Load paper that matches the size setting and then press the [START] key to begin printing.
M
Michael Hicks MDAug 27, 2025
Why does my Sharp AL-1556 keep misfeeding paper?
- A
  Alexis WalkerAug 28, 2025
  If your Sharp All in One Printer is experiencing frequent paper misfeeds, there are several potential causes. Ensure you are using copy paper within the specified size and weight range. Avoid using curled or damp paper, and make sure the paper is loaded properly. Remove any pieces of misfed paper from inside the machine. If the tray is overloaded, remove some paper. Fan the paper before loading it, and adjust the guides on the bypass tray to match the paper width. When using the bypass tray, pull out the extension for larger paper sizes. For specific misfeed removal instructions, see "MISFEED REMOVAL".
P
Patricia YoungAug 26, 2025
How to adjust the exposure on my Sharp AL-1556 All in One Printer if copies are too dark or light?
- K
  ktannerAug 26, 2025
  If your Sharp All in One Printer is producing copies that are either too dark or too light, the original type may not be correctly selected. Try selecting AUTO with the [EXPOSURE] key, or manually adjust the exposure by pressing the appropriate keys. If AUTO was already selected, try adjusting the automatic exposure level.
B
brandontorresAug 25, 2025
Why does my Sharp AL-1556 All in One Printer not operate?
- P
  pfitzpatrickAug 25, 2025
  If your Sharp All in One Printer is not operating, several factors could be the cause. Ensure the machine is plugged into a grounded outlet and the power switch is turned ON. If the power save indicator is blinking, allow the machine to finish warming up. Also, check that the front or side cover is completely closed. If the machine is in auto power shut-off mode, press the [START] key. Finally, make sure the scan head locking switch is unlocked.
N
Natalie CantrellAug 23, 2025
What to do if my Sharp All in One Printer says 'MEMORY FULL, PRESS START TO RESUME'?
- L
  Larry RuizAug 23, 2025
  If the Sharp All in One Printer displays 'MEMORY FULL, PRESS START TO RESUME', it means data is being held in the memory. To resolve this, print the data or clear it from the memory.