On=Screen Display Menu
=
Power control setting allows you to save energy.
Example
[ PowerControl ]
1 Press MENU to display the MENU screen, and then
press 4/_ to select "Power Control".
2 Press A/Y to select a "No Signal Off" or "No
Operation Off", and then press ENTER.
3 Press 4/_ to select "Enable", and then press ENTER.
4 Press MENU to exit.
This function allows you to set the Power Saving level
in order to decrease the power consumption and
increase the backlight lifespan.
Standard: Optimizes power reduction based upon video
content. When set to "Standard", "_)" appears on the
screen.
Advanced: Optimizes power reduction based upon video
content and engages OPC. When set to "Advanced",
.... appears on the screen.
Off: This function does not work.
o "Power Saving" does not function when you set "AV
MODE" to "DYNAMIC (Fixed)".
o You cannot select a different Power Saving item for each
AV MODE.
When "Power Saving" is set, the "OPC" settings for all AV
Modes will automatically change.
--If you set "OPC" to "On" when "Power Saving" is set
to "Standard", then the "Power Saving" setting will
change to "Advanced".
--When you change the "Power Saving" setting from
"Advanced" to "Off" or to "Standard", "OPC" will be set
to "Off".
--"DYNAMIC (Fixed)" will remain set to "Off".
o When "Power Saving" is set to "Standard" or "Advanced",
the Power Saving leaf icon appears to the left of "OPC" in
the Picture menu screen.
= You can select Power Saving by pressing POWER
SAVING on the remote control unit. (See page 1 7.)
When set to "Enable", the power will automatically shut
down if there is no signal for 15 minutes.
o When it is 5 minutes before the power shuts down, the
remaining time will start to keep appearing every minute.
o "Disable" is the factory preset value.
o When a TV program finishes, this function may not operate.
When set to "Enable", the power will automatically shut
down if there is no operation for 3 hours.
o When it is 5 minutes before the power shuts down, the
remaining time will start to keep appearing every minute.
o "Disable" is the factory preset value.
Example
_} Setup
VOL CH
SAnG E
FREEZE MENU
O @
G
1 Press MENU to display the MENU screen, and then
press 41/_ to select "Setup".
2 Press ,&/V to select a specific adjustment item,
and then press ENTER.
o When you select "EZ Setup", "OH Setup", "Parental
CTRL" or "Reset", you can enter the 4-digit secret
number here. See page 25 for setting a secret number.
3 Press ,&/T (or 4t/),,) to select the desired setting,
and then press ENTER.
4 Press MENU to exit.
You can run EZ Setup again, even after setting up the
preset channels.
Language: Select from among 3 languages (English,
French and Spanish).
TV Location: Select "Home" or "Store" for the location
where you plan to install the TV. This product qualifies
for ENERGY STAR V3.0 in Home mode default setting.
® Ifyou select "Home", AV MODEwill beset to "SITkNDARD"
and Power Savingwill be set to "Advanced".
® Ifyou select "Store", you wi]]be able to set PictureReset
opt#ns. Inthis case, AV MODEwill be set to "DYNAMIC
(Fixed)"regardlessof whether PictureResetis "On" or "Off".
Whenyou set Picture Resetto "On",AV MODEwill be reset
to "DYNAMIC(Fixed)"if there isno operationfor 30 minutes.
When "Off"is selected,AV MODEwill beset to "DYNAMIC
(Fixed)".
® ENERGYSTAR qualificationis basedon AV MODE
"S[_,NDARD"
Air/Cable: Make sure what kind of connection is made
with your TV when selecting "Air" or "Cable".
CH Search: Channel auto search makes the TV look for
all channels viewable in the set area.
= See "Initial Setup" on page 14 for setting each item.
= If no channel is found, confirm the type of connection made
with your TV and try EZ Setup again.
= If you select "Analog Search Start" and initiate the channel
search, the CH Memory for Cable Digital will be deleted.
Q- 23
To Next Page
Loading...
