(4) CPU interface
Terminal
name
Pin
No.
I/O Function
CS 1 I Chip select for the CPU to access
the LC8213 (low sctive).
RD 2 I Read.Set to “L” when the CPU is
the read out the LC8213 register.
WR 3 I Write.Set to “L” when the CPU is
to the LC8213 register.
A2 4 I Address input for when the CPU
accesses LC8213.
A1 5
A0 6
D7 9 I/O
3 state
Bidirectional 8-bit data bus
D6 10
D5 11
D4 12
D3 14
D2 15
D1 16
D0 17
IREQ 20 O Interrupt request signal for the
CPU. By reading out the INTR
(interrupt request register) the CPU
can find the cause of the
interruption.IREQ is set to “L” when
the CPU reads INTR.
DREQ 21 O DMA request signal for the external
DMA controller. This will be set to
“H” in the following cases.
• Data exists in the EFIFO during
the coding processes.
• An empty space exists in the
DFIFO during decoding processes.
• The DBUF can read/write during
data transfer between the image
memory bus and CPU bus.
DACK 22 I DMA acknowledge signal from the
external DMA comtroller.If DACK is
set to “L” during coding or
decoding, EFIFO and DFIFO will
be accessed. DBUF will be
accessed if DACK is set to “L”
during data transfer between the
image memory bus and CPU bus.
(5) Image memory interface
Terminal
name
Pin
No.
I/O Function
MA23 54 O
3 state
Not used.
MA22 55
MA21 56
MA20 57
MA19 56
MA18 59
MA17 60
MA16 61
MA/MD15 62 I/O
3 state
Not used.
MA/MD14 64 Low-order 16-bit address and 16-
bit data bus for the image memory.
MA/MD13 65
MA/MD12 66
MA/MD11 67
MA/MD10 68
MA/MD9 69
MA/MD8 70
Terminal
name
Pin
No.
I/O Function
MA/MD7 71
MA/MD6 74
MA/MD5 75
MA/MD4 76
MA/MD3 77
MA/MD2 78
MA/MD1 79
MA/MD0 80
AEN 41 O This is set to “L” when the
LC8213 is the bus master to the
image memory.
If AEN = “H”, MA/MD, MRD,
MWR, IORD, IOWR, UDE and
LDE will be a HiZ output.
AST 42 O This signal indicates that an
address is being output to
MA/MD15 ∼ MA/MD0.
MDEN 43 O This signal indicates that the
LC8213 is using MA/MD15 ∼
MD0 as data buses.
USE 49 I/O
3 state
Not used.
LDE 48 I/O
3 state
This signal indicates that the low-
order bits of the data bus are
being used.
MRD 44 O
3 state
This is set to “L” when data is
being read out of the image
memory.
MWR 45 O
3 state
This is set to “L” when data is
being written into the image
memory.
IORD 46 O
3 state
Not used.
IOWR 47 O
3 state
Not used.
BREQ 37 O This signal is used for the LC8213
to request usage rights from the
image memory bus.
BACK 38 I Input signal allowing the LC8213
to use the image memory bus.
IDREQ 39 I Not used.
IDACK 40 O Not used.
READY 50 I This signal is used to delay the
read/write signal when using low
speed image memory or an I/O
device.
DTC 51 O Not used.
(6) Others
Terminal
name
Pin No. I/O Function
CKL 28 I External clock (Max.20NHz)
RESET 27 I Reset
TEST0 35 I For testing.This is normally fixed
to “L”.
TEST1 34
TEST2 33
TEST3 32
TEST4 30
V
DD
7, 31,
73
power supply (+ 5V)
V
SS
13, 29,
52, 63,
72
GND
AR-F152
12 – 17
To Next Page
Loading...
