Sharp AR-151

[9] SIMULATION, FAX SOFTWARE SWITCH, TROUBLE CODES
1. List of simulations
The simulations for the AR-F152 (with Fax functions) are shown in bold fonts.
Sim
No.
Kind of
main code
Sub
code
Operation
01 Optical
system
01 Mirror scan operation
02 SPF
Individual
load
operation
02
03
04
05
06
07
SPF sensor status display
Motor ON
Paper feed solenoid ON
Pressure release solenoid ON
(RSPF)
Resist clutch ON (RSPF)
Gate solenoid ON (RSPF)
05 Lamp ON
check
01
02
03
Operation panel display check
Fusing lamp ON + Cooling fan
HIGH/LOW speed
Copy lamp ON
06 Machine
individual
load
operation
01
02
Paper feed solenoid ON
Resist solenoid ON
07 Aging 01
06
Warm up display and aging with
jam
Intermittent aging
08 High
voltage
output check
01
02
03
06
Developing bias
Main charger (Grid high)
Grid voltage (Low)
Transfer charger
10 Other None Toner motor aging
14 Trouble
reset
None Cancel troubles other than U2
16 U2 trouble
reset
None Cancel of U2 trouble
20 Maintenance
counter
clear
01 Maintenance/mini-maintenance
counter clear
21 Counter
setup
(When
maintenance)
01
02
Maintenance cycle setup
Mini-maintenance cycle setup
22 Counter
display
01
02
04
05
06
08
12
14
17
18
20
21
22
23
24
Maintenance/mini-maintenance
counter display
Maintenance/mini-maintenance
preset display
Jam total counter display
Total counter display
Developer counter display
SPF counter display
Drum counter display
P-ROM version display
Copy counter display
Printer counter display
FAX print counter display
Scanner counter display
SPF jam total counter display
FAX reception counter display
FAX transmission counter
display
24 Special
counter
clear
01
04
06
07
08
09
10
11
13
14
Jam total counter clear
SPF counter clear
Developer counter clear
Drum counter clear
Copy counter clear
Printer counter clear
FAX transmission/reception
counter clear
FAX print counter clear
Scanner counter clear
SPF jam total counter clear
25 Main motor
ON
01
10
Main motor system ON + Cooling
fan low speed (For the duplex
model, the duplex motor is
simultaneously turned on.)
Polygon motor ON
Sim
No.
Kind of
main code
Sub
code
Operation
26 Various
setup
01
02
03
04
06
07
20
30
37
39
40
42
43
44
47
55
Manual feed setup
SPF setup
Second cassette setup
Machine duplex setup
Destination setup
Machine conditions check
Rear edge void setup
CE mark conformity control
ON/OFF setup
Cancel of stop at developer over
Memory capacity setup
Polygon motor OFF time setup
Transfer ON timing control setup
Side void setup
SPF document rear edge read
setup
FAX document rear edge scan
setup
CRUM destination display
30 Sensor
operation
check
(Standard
provision)
01 Paper sensor status display
43 Fusing
temperature
setup
01
04
05
09
Normal copy
Fusing temperature setup 2
Duplex mode fusing temperature
setup
Postcard size paper fusing control
setup
46 Exposure
adjustment
01
12
13
14
15
19
Copy density adjustment
FAX density overall adjustment
FAX density adjustment
(Standard mode)
FAX density adjustment (Fine
character mode)
FAX density adjustment (Super
Fine mode)
γ Table adjustment (Copy mode)
48 Magnification
ratio
correction
01 Front/rear scan direction
50 Lead edge
adjustment
01
10
18
19
Lead edge image position
adjustment
Paper lead edge/rear edge void
adjustment
Paper center offset +
OC/Document center offset +
SPF document center offset
Memory reverse position
adjustment
Duplex copy rear edge void
adjustment
51 Timing
adjustment
02
06
Resist quantity adjustment
SPF exposure correction
61 Laser
system
operation
03 Polygon motor check
(HSYNC output check)
63 Shading 01 Shading check
64 Self print 01 Self print only with the engine (1
by 2 mode)
66 FAX PWB
check
None Simulation on the FAX panel
(For details, refer to the FAX
simulation.)
67 Program
Download
14 PCL PWB program download
AR-F152
9 – 1