[JOB#926] MRS = 0400
#926-A: Not used (Fixed at "0")
#926-B: 1. Program reset at PGM 2 mode
1. Program reset at PGM2 mode 926-B
Disable 0
Enable 4 ★
#926-C: 1. Open store/Close store with on-line
2. Send AT command string with JOB#500 (Open store)
3. Send AT command string with JOB#501 (Close store)
1. Open
store/Close
store with
on-line
2. Send AT
command
string with
JOB#500
(Open store)
3. Send AT
command
string with
JOB#501
(Close store)
926-C
No
No
No 0 ★
Yes 1
Yes
No 2
Yes 3
Yes
No
No 4
Yes 5
Yes
No 6
Yes 7
#926-D: 1. Receive on-line channel in close store
1. Receive on-line channel in close store 926-D
No 0 ★
Yes 4
[JOB#927] NOT USED: MRS = 0000
[JOB#928] NOT USED: MRS = 0000
[JOB#929] MRS = 0000
#929-A, B, C: Not used (Fixed at "000")
#929-D: 1. Taxable status of PLU which is set at "Non-taxable" by
PGM
1. Taxable status of PLU which is set at
"Non-taxable" by PGM
929-D
According to its associated Department 0 ★
Non-taxable 2
[JOB#930∼941] MRS = 0000
RESET REPORT COUNTER
JOB # Function
930 Z1 report counter
933 Hourly Z1 report counter
934 PLU Z1/Z2 report counter
935 Cashier Z1/Z2 report counter
937 Z2 report counter
939 31 day daily net Z2 report counter
[JOB#942, 943, 969] MRS = 0000000000000
GT COUNTER PRESETTING
JOB # Function
942 GT2 (Positive GT)
943 GT3 (Negative GT)
969 TRAINING GT
Note: GT1 is obtained by calculation
Equation: GT1=GT2-GT3
[JOB#944] MRS = 0000
PGM2 secret code presetting
NOTE: When the secret code "0" is programmed, the secret code
entry is be inhibited.
[JOB#950] MRS = STANDARD KEY LAYOUT
Free key layout (Except for department keys and direct PLU keys.)
[JOB#951] MRS = STANDARD KEY LAYOUT
Free key layout (department keys and direct PLU keys)
• Programming of the keys to be dept keys or direct PLU keys on
the keyboard.
• Key No. is assigned to each key which is supposed to be dept.
Key or direct PLU key by depressing the key after entering the key
No.
• Those keys programmed by this job No. will be dept. keys if dept.
code is assigned, and will be direct PLU keys if PLU code is
assigned in the PGM2 mode.
CA/ATJob#
ABCD
Initial value of Z countr
@/FOR
"0000"
CA/ATJob#
0000000000000
13 digits
@/FOR
0
CA/AT944
XXXX
4 digits
@/FOR
0
Free key
@/FOR
CA/AT
@/FOR
Key number automatic
increment
Key number manual
increment
Initial setting
XXX
Key No.
To inhibit
SBTL
increment key No.
950
Free key
@/FOR
CA/AT
@/FOR
Key No.
Key number automatic
increment
Key number manual increment
To inhibit
SBTL
increment key No.
951
XXX
– 12 –
To Next Page
Loading...
Need help?
General
