11
LC-32HT1U
Appendix
Removing the stand
Before detaching (or attaching) the stand, unplug the AC cord from the AC INPUT terminal.
CAUTION
• Do not remove the stand from the TV unless using an optional wall mount bracket to mount it.
Before attaching/detaching stand
• Before performing work make sure to turn off the TV.
• Before performing work spread cushioning over the base area to lay the TV on. This will prevent it from being
damaged.
NOTE
• To attach the stand, perform the above steps in reverse order.
2
Unfasten the four screws used to
secure the stand in place.
1
Unfasten the screw used to secure the
bracket in place.
Setting the TV on the wall
CAUTION
• Installing the Liquid Crystal Television requires special skill that should only be performed by qualified service
personnel. Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper
mounting or mounting that results in accident or injury.
Using an optional bracket to mount the TV
• You can ask a qualified service professional about using an optional bracket to mount the TV to the wall.
• Carefully read the instructions that come with the bracket before beginning work.
Hanging on the wall
Wall mount bracket. (See the bracket instructions for details.)
About setting the TV angle
Vertical mounting Angular mounting
3
Detach the stand from the TV.
(Hold the stand so it will not drop
from the edge of the base area.)
10°
Appendix
• No power
• Unit cannot be operated.
• Remote control unit does not
operate.
• Picture is cut off/with sidebar
screen.
• Strange color, light color, or color
misalignment
• Power is suddenly turned off.
• No picture
• No sound
Problem Possible Solution
• Check if you pressed TV POWER on the remote control unit.
If the indicator on the TV is off, press POWER on the TV.
• Is the AC cord disconnected?
• External influences such as lightning or static electricity may cause improper
operation. In this case, operate the unit after first turning on the power of the TV
or unplugging the AC cord and replugging it in after 1 or 2 minutes.
• Is the FUNCTION set correctly? Set it to the TV setting position.
• Are the batteries inserted with polarity (
+
,
Ð
) aligned? (See the OPERATION
MANUAL FOR HOTEL OPERATOR.)
• Are the batteries worn out? (Replace with new batteries.)
• Are you using it under strong or fluorescent lighting?
• Is a fluorescent light illuminated near the remote control sensor?
• Is the image position correct? (See the OPERATION MANUAL FOR HOTEL
OPERATOR.)
• Are screen mode adjustments such as picture size made correctly? (See the
OPERATION MANUAL FOR HOTEL OPERATOR.)
• Adjust the picture tone. (See the OPERATION MANUAL FOR HOTEL
OPERATOR.)
• Is the room too bright? The picture may look dark in a room that is too bright.
• Is the sleep timer set? (See the OPERATION MANUAL FOR HOTEL
OPERATOR.)
• Check the power control settings. (See the OPERATION MANUAL FOR HOTEL
OPERATOR.)
• The unit’s internal temperature has increased.
Remove any objects blocking vent or clean the vent.
• Is the connection to other components correct? (See the OPERATION MANULA
and the OPERATION MANUAL FOR HOTEL OPERATOR.)
• Is the correct input signal source selected for the connection? (See the
OPERATION MANUAL FOR HOTEL OPERATOR.)
• Is the correct input selected? (See the OPERATION MANUAL FOR HOTEL
OPERATOR.)
• Is the picture adjustment correct? (See the OPERATION MANUAL FOR HOTEL
OPERATOR.)
• Is the volume too low? (See the OPERATION MANUAL FOR HOTEL
OPERATOR.)
• Is “Variable” selected in “Output Select”? (See the OPERATION MANUAL FOR
HOTEL OPERATOR.)
Troubleshooting
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly
delayed. This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near
a heater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction.
Storage temperature:–4°F to
+
140°F (
–
20°C to
+
60°C)
Troubleshooting-Digital broadcasting
Error messages about reception of broadcast
Examples of error messages
displayed on the screen
Error code Possible Solution
• Failed to receive broadcast.
E202
• No broadcast now.
E203
• Check the antenna cable. Check that the antenna is correctly
set up.
• Check the broadcast time in the program guide.
To Next Page
Loading...
Need help?
General
