Sharp PN-V550 - Specifications

60
E
Specications
n
Product Specications
Model PN-V551 PN-V550
LCD component
55" Class [54-5/8 inch (138.8cm) diagonal] TFT LCD
Max. resolution (pixels)
1920 x 1080
Max. colors
Approx. 16.77 million colors
Pixel pitch
0.63 mm (H) × 0.63 mm (V)
Max. brightness (typical) *
1
700 cd/m
2
(default: 550 cd/m
2
) 500 cd/m
2
(default: 400 cd/m
2
)
Contrast ratio (typical) *
1
3500 : 1 4000 : 1
Viewing angle
178° right/left/up/down (contrast ratio ≥ 10)
Screen active area inch (mm)
47-5/8 x 26-13/16 (1209.6 x 680.4)
Computer input signal
Digital (DVI 1.0 standard-compliant), Analog RGB (0.7 Vp-p) [75
Ω
],
DisplayPort 1.1a
Sync signal
Horizontal/vertical separate (TTL: positive/negative), Sync-on-green*
2
,
Composite sync (TTL: positive/negative)*
2
Video color system
NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM
Plug and play
VESA DDC2B
Power management
VESA DPMS, DVI DMPM
Input terminals
PC/AV HDMI x 1
Mini D-sub 15 pin, 3 rows x 1
PC DisplayPort x 1
DVI-I 29 pin (HDCP compatible) x 1
Audio
3.5 mm mini stereo jack x 1
Serial (RS-232C)
D-sub 9 pin x 1
Control kit
Control kit x 1
Output terminals PC
DisplayPort x 1
DVI-D 24 pin (HDCP compatible) x 1
Audio
3.5 mm mini stereo jack x 1
Serial (RS-232C)
D-sub 9 pin x 1
LAN terminal 10 BASE-T/100 BASE-TX
Power requirement AC 100 V - 240 V, 2.4 A, 50/60 Hz AC 100 V - 240 V, 2.1 A, 50/60 Hz
Operating temperature
*
3
32°F to 104°F (0°C to 40°C)
Operating humidity 20% to 80% (no condensation)
Power consumption
(Maximum / input signal waiting mode
*
4
*
5
/
standby mode
*
6
)
210 W / 2.0 W / 2.0 W 185 W / 2.0 W / 2.0 W
Dimensions (excluding protrusions) inch (mm)
Approx. 47-3/4 (W) x 4-1/2 (D) x 26-15/16 (H) (1213.5 x 113.8 x 684.3)
Weight lbs. (kg)
Approx. 60.2 (27.5) Approx. 55.1 (25.0)
*1 Brightness and Contrast ratio will depend on input mode and other picture settings. Brightness level will decrease over time. Due to the
nature of the equipment, it is not possible to precisely maintain a constant level of brightness.
*2 D-Sub input terminal only.
*3 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP. In such
cases, please check the temperature condition specied by the optional equipments.
*4 When AUTO INPUT CHANGE is set to OFF.
*5 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W. (during PC input)
*6 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W.
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement
without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
n
PN-ZR01A (optional) Product Specications
Model PN-ZR01A
Remote control sensor box dimensions inch (mm)
Approx. 1-3/8 (W) x 7/8 (D) x 5-1/8 (H) (34.2 x 23 x 130)
Remote control sensor box weight lbs. (kg)
Approx. 0.220 (0.1)