Sharp PN-V600A - Remote Control Mode

21
E
Remote Control Mode
Withtheremotecontrolunitit’spossibletoperformoperation
of...
• Theprimarymonitor
• MonitorswithaspeciedIDNo.
• Allprimary/secondarymonitors
It’s necessary to specify which type of operation will be
performed in advance.
1. If using the remote control unit, press
MODE
for approx 5
seconds.
If using the monitor buttons, hold both
and at
the same time on the primary.
▲
▲
THIS MONITOR ONLY
REMOTE CONTROL MODE
MODE
OK CANCEL
Operate this monitor.
2. Press
or
, select the mode, then perform
settings.
THIS MONITOR ONLY
Performs operation of only the primary using the remote
control unit.
[Example]Ifthevolumeislowered,thevolumeoftheprimary
will lower.
Secondary
ID No.: 2
Secondary
ID No.: 3
Primary
ID No.: 1
Secondary
ID No.: 4
VOLUME 10
Press to lower the volume
SPECIFIED MONITOR
PerformsoperationofamonitorwithaspeciedIDNo.using
the remote control unit.
Press
or toselectIDNo.,thenpress or to
selecttheIDNo.ofthemonitorthatyouwilloperate.
*Whenitreceivessignalsfromtheremotecontrolunit,
“Operatingspeciedmonitor.”willbedisplayedonthe
primary screen.
[Example.]IfIDNo.issetto3andthevolumeislowered,
thevolumeofthemonitorforIDNo.:3willlower.
Secondary
ID No.: 2
Secondary
ID No.: 3
Primary
ID No.: 1
Secondary
ID No.: 4
VOLUME 10
Press to lower the volume
WhenyouwouldliketoconrmtheIDNo.thatissettothe
monitor, press
or toselectIDNo.DISPLAY,then
press
.TheIDNo.willbedisplayedonthescreen.
ALL MONITORS
Performs operation of all primary/secondary monitors.
*
ALL
will be displayed on the menu of the primary.
*Whenitreceivessignalsfromtheremotecontrolunit,
“Operating all monitors.” will be displayed on the secondary
screen.(Excludingpowerandinputmodeselectionoperation)
*Settingsmaynotbereecteddependingonthestateofthe
connected monitors.
[Example]IfthepowerfortheprimaryisturnedON,thepower
for all the monitors will be turned ON.
Secondary
ID No.: 2
Secondary
ID No.: 3
Primary
ID No.: 1
Secondary
ID No.: 4
Power ON Power ON
Power ON
Power ON
Press to turn the power ON
POWER
Press or toselectEXPANDITEM,andpress or
to select to perform this action or not.
OFF ...........Forallmonitors,onlypower,inputmode
selection, and product information display
operationswillberecognized.
ON .............Forallmonitors,alloperationswillbe
recognized.
After returning to the normal screen with
procedure3,when5minuteshavepassedfrom
the end of operation, it will automatically return
toOFF.
ALL [EXPAND ITEM]
will be displayed on the menu of
the primary.
* EvenwhenREMOTECONTROLMODEisset
to ALL MONITORS, certain settings such as
LANsettingsandIDNo.settingswillnotbe
reectedontheothermonitors.
3. Press
or to select OK, then press
MENU
and
return to the normal screen.
4. Perform operation.
Caution
• WhentheremotecontrolmodeissettoALLMONITORS
andEXPANDITEMissettoON,performingremotecontrol
operationsthatchangeadjustmentvalueswillresultin
thesecondaryadjustmentvaluesbeingthesameasthe
primaryadjustmentvalues.
Secondary
ID No.: 2
Secondary
ID No.: 3
Primary
ID No.: 1
Secondary
ID No.: 4
Secondary
ID No.: 2
Secondary
ID No.: 3
Primary
ID No.: 1
Secondary
ID No.: 4
VOLUME 12 VOLUME 11
VOLUME 10
VOLUME 9
VOLUME 10 VOLUME 10
VOLUME 10
VOLUME 10
Press to lower the volume
Becarefulofthiswhenadjustingindividualdisplays.
TIPS
• Youcancopythesettingvaluesoftheprimarytoother
monitorswithCOPYSETTINGVALUE.(Seepage25.)
• Thebuttonsonthemonitoritself(primary)arealsoeffective
in remote control mode.
• Whenmonitorsconnectedinadaisychainareinstandby
modeforLOWPOWER,operationcannotbeperformedfor
subsequentmonitors.