<D When connecting wires to the Device terminals, consider the specified conductor cross section and stripped length. Do not connect multiple
wires into a single terminal.
<D For security reasons, a er you success· fully connect the Device to the local Wi-Fi network, we recommend that you disable
or password-protect the Device AP (Access Point).
<D To perform a factory reset of the Device, press and hold the Control button for 1O seconds.
<D To enable the access point and the Blue tooth connection of the Device, press and hold the Control button for 5 seconds
<D Make sure that the Device is up-to-date with the latest firmware version. To check for updates, go to Settings> Firmware. To install the
updates, connect the Device to your focal
Wi·Fi network. For more details, see https:// shelly.link/wig.
<D Do not use L terminal(s) of the device to power other devices
1.
Connect a switch or a button to a SW ter minal of the Device and the Live wire as shown in section Wiring diagrams.
2.
Connect the Live wire to the L terminal and
the Neutral wire to the N terminal.
Specifications
Physical
Size (HxWxD):
37x42x17 mm/
1.46x1.65x0.66 in Weight 18 g / 0.63 oz
Screw terminals max torque:
0.4 Nm/ 3.5 lbin
Conductor cross section: 0.2 to 2.5 mm
2
/ 24 to 14 AWG (solid, stranded, and bootlace ferrules)
Conductor stripped length: 6 to 7 mm/
0.24 to 0.28 in
Mounting: Wall console/ In-wall box Shell material: Plastic
Environmental
Ambient working temperature:
-20·c to 40°c / ·5"F to 105°F
•
Humidity: 30% to 70% RH
•
Max. altitude: 2000 m / 6562 ft Electrical
•
Power supply: 110 - 240 V~ 50/60 Hz
•
Power consumption:< 1 W Sensors, meters
•
Internal-temperature sensor: Yes Radio
Wi-Fi
Protocol: 802.11 b/g/n
RF band: 2401 • 2483 MHz Max. RF power:< 20 dBm
Range: Up to 50 m / 165 ft outdoors, up to 30 m / 99 ft indoors (depending on local conditions)
Bluetooth
Protocol: 4.2
RF band: 2400 • 2483.5 MHz
Max. RF power: < 4 dBm
Range: Up to 30 m / 100 ft outdoors, up to 10 m / 33 ft indoors (depending on local conditions)
Microcontroller unit
•
CPU:
ESP-Shelly-C38F
•
Flash: 8 MB Firmware capabilities
Webhooks (URL actions): 20 with 5 URLs per hook
Scripting: Yes MQTT: Yes
Encryption: Yes Shelly Cloud inclusion
The Device can be monitored, controlled, and set up through our Shelly Cloud home
automation service. You can use the service through
either our Android, iOS, or Harmony OS mobile application or through any internet
browser at https://control.shelly.cloud/.
If you choose to use the Device with the application and Shelly Cloud service, you can find instructions on how to connect the Device
to the Cloud and control it from the Shelly app in the application guide: https://shelly.link/app-guide.
The Shelly mobile application and Shelly Cloud service are not conditions for the De vice to function properly. This Device can be used
standalone or with various other home automation platforms.
Troubleshooting
In case you encounter problems with the installation or operation of the Device, check its knowledge base page: https://shelly.link/i4_Gen3
Declaration of Conformity
Hereby, Shelly Europe Ltd. declares that the radio equipment type Shelly i4 Gen3 is in compliance with Directive 2014/53/EU, 2014/35/EU,
2014/30/EU, 2011/65/EU. The
full text of the EU declaration of conformity is available at the following internet address: https://shelly.link/i4_Gen3_DoC Manufacturer:
Shelly Europe Ltd.
Address: 103 Cherni vrah Blvd., 1407 Sofia, Bulgaria
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Official website: https://www.shelly.com Changes In contact information are pub lished by the Manufacturer on the official website.
All rights to the trademark Shelly® and other intellectual rights associated with this Device belong to Shelly Europe Ltd.
To Previous Page
Loading...
