Shop fox D2260A User Manual

Introduction
Your new Model D2260A Mini Mobile Base (Figure 1) is
designed to give you a stable and mobile platform upon
which to mount machinery and equipment with a variety
of base dimensions and weights.
Specifications
• MinimumInsideDimensions .............. 10
1
⁄2" x 14
1
⁄2"
• MaximumInsideDimensions ............. 21
1
⁄2" x 17
1
⁄2"
• MaximumWeightCapacity ....................... 600 lbs
Tools
Tape Measure ....................................................1
WrenchesorSockets13mm ...................................2
WrenchesorSockets14mm ...................................2
Light Machine Oil (Optional) ...................... As Needed
Crowbar(Optional) .............................................1
Rubber Mallet (Optional) ......................................1
6" 2x4's (Optional) ..............................................2
6" 2x6 (Optional) ................................................1
12" 4x4 (Optional) ..............................................1
Inventory (Figure 2) Qty
A. SwivelCasters ..............................................2
B. FixedCasters ...............................................2
C. LeftCornerBracket .......................................1
D. RightCornerBracket ......................................1
E. RightCornerBracketw/FootPost ......................1
F. LeftCornerBracketw/FootPost .......................1
G. SideRails15
1
⁄8" Long .....................................2
H. SideRails10
5
⁄8" Long ....................................2
I. KnobsM12-1.75 ............................................2
J. Feet ..........................................................2
K. Hardware Bag (not shown)
—HexBoltsM8-1.25x16(Brackets,Casters) ....... 32
—LockNutsM8-1.25(Brackets) ....................... 16
—LockWashers8mm(Casters) ........................ 16
—FlatWashers8mm(Casters) ......................... 16
—HexNutsM8-1.25(Casters) .......................... 16
Figure 1. Model D2260A.
Figure 2.Inventory.
A
B
D
E
F
G
H
IJ
C
Do not use the Model D2260A until
you have read and understood this
instruction sheet and completed the
entire assembly procedure. Serious
personal injury may occur if you ignore
this warning.
COPYRIGHT © MAY, 2009 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in China#11850BL
Model D2260A
Mini Mobile Base
Instruction Sheet
Phone#:(360)734-3482•OnlineTechSupport:tech-support@shopfox.biz•Web:www.shopfox.biz

Shop fox D2260A Specifications

General

Brand	Shop fox
Model	D2260A
Category	Racks & Stands
Language	English

Summary

Introduction

Specifications

Tools

Inventory

Preparation

Check Machine Compatibility

Verify machine weight and footprint against base specifications.

Determine Swivel Caster Placement

Choose end for swivel casters for optimal maneuverability.

Plan Machine Mounting Method

Decide if lifting or building base around the machine.

Assembling Base

Mount Casters to Corner Brackets

Attach swivel and fixed casters to corner brackets using specified hardware.

Assemble Base Frame

Lay out brackets, insert rails, and adjust dimensions to fit machine footprint.

Secure Frame Connections

Fasten rails to brackets and install foot posts with hardware.

Adjust Feet Position

Set knobs to raise feet off the floor for mobility.

Assembling Base Around Machine

Prepare and Position Components

Install foot posts, rails, and position against machine.

Secure Frame Assemblies

Fasten front and rear rails to corner brackets.

Integrate and Mount Casters

Slide rear assembly onto rails and attach swivel casters.

Final Tightening and Checks

Tighten all hardware and confirm assembly completion.

Making a Base Plate

Prepare Plywood Base Plate

Glue and screw plywood pieces together to create a thick base.

Attach Base Plate to Mobile Base

Drill and secure the base plate to the mobile base corners.

Mount Machine to Base Plate

Secure the machine to the prepared base plate.

Mounting Machine onto Mobile Base

Final Base Checks and Positioning

Check fasteners, clearances, and carefully lower machine onto base.

Verify Machine Seating and Load

Check for stress, deflection, and confirm weight limits.

Using Mobile Base

Prepare for Movement

Disconnect power, clear pathway, and adjust feet to lift base.

Move Machine to Location

Push machine from lowest point, ensuring stable movement.

Secure Base and Check Stability

Firmly contact feet with floor and verify stability.

D2260A Parts Identification

Component List and Diagram

Reference diagram and list for all mobile base components.