What to do if my Shott Heat Pump does not work and error message EE 2 is displayed?
If your Shott Heat Pump displays error message EE 2 and isn't working, the ambient temperature sensor may be incorrectly connected or defective. Check the sensor resistance value and replace it if necessary. You can also replace the control board.
What to do if my Shott BP-50HS-A is running and error message EE 3 is displayed?
If your Shott Heat Pump displays error message EE 3 while running, the compressor temperature sensor may be incorrectly connected or defective. Check the sensor resistance value and replace if necessary. You can also replace the control board.
What to do if my Shott BP-50HS-A does not work and error message EE 1 is displayed?
If your Shott Heat Pump displays error message EE 1 and isn't working, the pool temperature sensor may be incorrectly connected or defective. Check the sensor resistance value and replace it if necessary. You can also replace the control board.
What to do if my Shott BP-50HS-A Heat Pump does not start?
If your Shott Heat Pump doesn't start, first ensure that the 3 minutes required for pump start have elapsed. If the pool temperature is at or above the set temperature, the pump will only start when the pool temperature drops below the set temperature. Finally, confirm that the pump operating mode is set to the required mode.
Why is my Shott Heat Pump not working and error message EE 6 is displayed?
If your Shott Heat Pump displays error message EE 6 and isn't working, it could be due to several reasons. The compressor temperature might be too high, so wait until it drops. There could be a refrigerant circuit leak, so check for leaks and replace any defective parts. Alternatively, the capillary circuit might be clogged, in which case it should be replaced.
What to do if my Shott Heat Pump is running but the water is not heating?
If your Shott Heat Pump is running but not heating the water, first ensure that air exits the front part of the heat pump. If the heat pump was just installed, allow 24 to 48 hours to reach the set temperature. If the pool water has significantly cooled since the last use, it may take 24 to 36 hours to reach the desired temperature.
What does it mean if my Shott BP-50HS-A displays error message EE 8 and doesn't work?
If your Shott Heat Pump displays error message EE 8 and does not work, it indicates that the control board wiring is defective. Check the wiring.
What does it mean if my Shott BP-50HS-A Heat Pump displays error message EE 4?
If your Shott Heat Pump is running and displays error message EE 4, it means the automatic defrost did not run correctly. Increase the water flow at the pump inlet.
What does it mean if my Shott Heat Pump displays error message EE d?
If your Shott Heat Pump displays error message EE d, it means there are functional parameter changes and parameter 9 is not set to 1. Set the correct parameter values to 1.
What does it mean if my Shott BP-50HS-A Heat Pump displays error message EE 3?
If your Shott Heat Pump is running and displays error message EE 3, it indicates that the compressor temperature sensor is incorrectly connected or defective. Check the sensor resistance value and replace it if necessary.
Formal statement of compliance with EU directives for the machinery.
Details the warranty period, conditions, and exclusions for the product.
Specific warranty applicability and validation requirements within EU member countries.
Limitations on warranty coverage, such as consumer sales and misuse.
Essential safety guidelines for using heated swimming pools to prevent accidents.
Tips and recommendations for optimizing heat pump energy consumption and performance.
Defines the intended use and application of the SERIES BP heat pumps.
Procedures for checking the unit upon arrival and safe methods for handling.
Guidance on selecting an appropriate location and mounting the heat pump.
Steps for installing the mains connection socket, ensuring correct IP grade and grounding.
Procedure for safely replacing the heat pump's mains connection cord.
Explanation of the heat pump control panel buttons, display, and basic operations like turning on/off.
Procedures for starting the unit, selecting operating modes, and adjusting set temperatures.
Configuration of minimum working temps, automatic start, and standby modes.
Functions for manual defrost, locking controls, and viewing sensor temperatures on the display.
Configuration options for defrost cycles and compressor protection settings.
Adjusting pool temperature regulation, defrost start/stop temperatures.
Setting defrost repetition time, duration, and compressor temperature limits.
Configuring automatic restart, operating mode, and temperature deviation settings.
Selecting control mode and understanding manometer readings for pressure monitoring.
Details on ambient, pool, flow, compressor, and plate heat exchanger sensors.
Explains the role of the high pressure sensor in protecting the compressor.
Explains the role of the low pressure sensor in protecting the compressor.
Table providing resistance values for temperature sensors at various temperatures.
Table providing resistance values for the compressor temperature sensor.
Tasks for users and specialized technicians for regular checks and upkeep.
Procedures for protecting the unit during winter and recommissioning in spring.
Identifies common issues like no start, no heating, or frost, and provides solutions.
Guides for resolving specific error codes displayed by the heat pump.
Lists and illustrates spare parts for the BP-xxHS-A model, with part numbers.
Lists and illustrates spare parts for the BP-xxWS-B model, with part numbers.
Specific instructions for replacing key components like manometer, sensors, filter, and capillary.
To Next Page
General
