What to do if my Shott BP-160HS-A is running but the water is not heating?
If your Shott Heat Pump is running but not heating the water, first ensure that air exits the front part of the heat pump. If the heat pump was just installed, allow 24 to 48 hours to reach the set temperature. If the pool water has significantly cooled since the last use, it may take 24 to 36 hours to reach the desired temperature.
What to do if my Shott BP-160HS-A Heat Pump displays error message EE b?
If your Shott Heat Pump shows error message EE b, it indicates insufficient water flow. Increase the water flow in the hydraulic circuit that supplies the heat pump and restart after 2 minutes. Alternatively, the flow sensor might be incorrectly connected or defective, so check the connections and replace the sensor if necessary.
What to do if my Shott Heat Pump does not turn on?
If your Shott Heat Pump does not turn on, ensure that you have followed all instructions. Additionally, check the mains connection line protection device fuse and the contact switch; reset the switch or replace the fuse if necessary.
What does it mean if my Shott BP-160HS-A Heat Pump displays error message EE 6 and doesn't work?
If your Shott Heat Pump displays error message EE 6 and does not work, it could be due to several reasons. The compressor temperature might be too high, so wait for it to drop. Alternatively, there could be a refrigerant circuit leak, in which case you should check for leaks with a leak detector and replace any defective parts. Finally, the capillary circuit might be clogged, requiring you to replace it.
What to do if my Shott Heat Pump is not working and shows error message EE 1?
If your Shott Heat Pump is not working and displays error message EE 1, the pool temperature sensor may be incorrectly connected or defective. Check the sensor resistance value and replace it if necessary.
Why won't my Shott Heat Pump start?
Your Shott Heat Pump might not start for several reasons. Ensure that the 3 minutes required for pump start have elapsed. If the pool temperature is greater than or equal to the set temperature, the pump will start when the pool temperature is lower. Also, verify that the pump operating mode is set to the required mode.
What to do if my Shott BP-160HS-A Heat Pump has frost on the plate heat exchanger?
If there is frost on the plate heat exchanger of your Shott Heat Pump, it could be due to a low ambient temperature or high humidity. You can start a manual defrost. Another possible cause is a pressure refrigerant drop, in which case you should replace the refrigerant.
What to do if my Shott BP-160HS-A Heat Pump is leaking water?
If water is leaking from your Shott Heat Pump, it could be due to condensation accumulation. Put the heat pump in standby; if the leak stops, it's normal condensation. Alternatively, there may be a water leak from the water exchanger or hydraulic unit connection devices, in which case you should tighten the fastening nut.
What does error message EE 7 on my Shott Heat Pump mean?
If your Shott Heat Pump displays error message EE 7 and doesn't work, it indicates a current dispersion. Replace the defective component, which could be the compressor, fan, four way valve, or electronic board.
What to do if my Shott Heat Pump displays error message EE c?
If your Shott Heat Pump displays error message EE c, it means the ambient temperature is under -15 [°C]. Wait until the ambient temperature rises to start the heat pump.
Covers product warranty, safety regulations for heated pools, and symbol key explanations.
Visual representation of the typical hydraulic circuit layout for the heat pump installation.
Emphasizes electrical safety, voltage requirements, and protection device installation.
Essential precautions and critical checks before the initial heat pump start-up.
Guide to using the control panel and instructions for powering on the heat pump.
How to choose between heating, cooling, or other operating modes for the heat pump.
Instructions for setting temperature and defining minimum working/restart parameters.
Configuring automatic start/standby and performing manual defrost procedures.
Lists parameters for models and setting pool temperature regulation range.
Setting compressor protection limits and selecting the heat pump's operating mode.
Setting maximum temperature deviation and choosing the control mode.
Details the high-pressure sensor's function in stopping the compressor under excessive pressure.
Describes the low-pressure sensor's role in stopping the compressor under insufficient pressure.
To Next Page
General
