Siemens 7SA513 - Page 344

$SSHQGL[6$
9

&*&
¿©©©©§©©©©©©©©©©©©©§©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©§©©§©©§©§©©©¤
FNo.Abbreviation  Meaning OpFtEIOT
¨©©©©ª©©©©©©©©©©©©©ª©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©ª©©ª©©ª©ª©©©
 164U supervisionMeasured value supervision of voltages   O
 165Failure ÉUp-eFailure: Voltage sum superv. (ph-e) CG   OT
 166Failure ÉUp-pFailure: Voltage sum superv. (ph-ph) CG   OT
 167Failure UsymmFailure: Voltage symmetry supervision CG   OT
 168Failure UmeasFailure: Measuring voltages absent CG   OT
 169Fuse-Failure Fuse failure monitor operated (>10s) CG   OT
 170FFM pick-up Fuse failure monitor pick-up CG   
 171Fail.PhaseSeqFailure: Phase sequence supervision CG   OT
 203Flt.RecDatDelFault recording data deleted C    
 204Flt.Rec.viaBIFault recording initiated via bin.inputC    
 205Flt.Rec.viaKBFault recording initiated via keyboard C    
 206Flt.Rec.viaPCFault recording initiated via PC interfC    
 244D Time= Diff. time of clock synchronism  M   
 301Syst.Flt Fault in the power system CGC   
 302Fault Flt. event w. consecutive no.  C   
 351>CB Aux. L1 >Circuit breaker aux. contact: Phase L1   IOT
 352>CB Aux. L2 >Circuit breaker aux. contact: Phase L2   IOT
 353>CB Aux. L3 >Circuit breaker aux. contact: Phase L3   IOT
 354>CB Aux.3p cl>CB aux. contact:3poles closed (series)   IOT
 355>CB Aux.1p cl>CB aux. contact:1pole closed(parallel)   IOT
 356>Manual Close>Manual close    IOT
 357>CloseCmd.Blo>Block all close commands from externalCG  IOT
 361>VT mcb Trip >U Line side VT MCB tripped CG  IOT
 362>V2 mcb Trip >U2 Busbar side VT MCB tripped CG  IOT
 381>1p Trip Perm>External auto-reclose ready for 1pole CG  IOT
 382>Only 1pole >External AR programmed for 1pole only CG  IOT
 383>RAR Release >Release overreach zones RAR CGCG IOT
 384>DAR Release >Release overreach zones DAR CGCG IOT
 501Device FltDetGeneral fault detection of device     OT
 502Dev. Drop-offGeneral drop-off of device  C   
 503Dev.FltDet L1General device fault detection: Ph. L1     OT
 504Dev.FltDet L2General device fault detection: Ph. L2     OT
 505Dev.FltDet L3General device fault detection: Ph. L3     OT
 506Dev.FltDet N General device fault detection: Ph. NOT
 511Device Trip General trip of device   G  OT
 512Dev.Trip 1pL1General 1pole trip of device: Phase L1     OT
 513Dev.Trip 1pL2General 1pole trip of device: Phase L2     OT
 514Dev.Trip 1pL3General 1pole trip of device: Phase L3     OT
 515Dev.Trip 3p General 3pole trip of device     OT
 516Dev.Trip forwGeneral trip for fault in forward dir.     OT
 517Dev.Trip rev.General trip for fault in reverse dir.  COT
 521IL1/In= Interrupted current: Phase L1(I/In)  C   
 522IL2/In= Interrupted current: Phase L2(I/In)  C   
 523IL3/In= Interrupted current: Phase L3(I/In)  C   
 545T-Drop Time from fault detection to drop-off 
 546T-Trip Time from fault detection to trip     
 561Manual Close Circuit breaker manually closed (pulse)C    OT
 562Man.Close CmdCB close command for manual closing     OT
 563CB Alarm SuppCB alarm suppressed     OT
 601IL1[%] = Current in phase IL1 [%] =  M   
 602IL2[%] = Current in phase IL2 [%] =  M   
 603IL3[%] = Current in phase IL3 [%] =  M   
 621UL1E[%]= UL1E [%]=  M   
 622UL2E[%]= UL2E [%]=  M   
 623UL3E[%]= UL3E [%]=  M   
 624UL12[%]= UL12 [%] =  M   
 625UL23[%]= UL23 [%] =  M   
 626UL31[%]= UL31 [%] =  M   
¥©©©©¦©©©©©©©©©©©©©¦©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©©¦©©¦©©¦©¦©©©¾
www . ElectricalPartManuals . com