en Time-setting options
14
When rapid heat up is complete, a signal sounds. The
c symbol goes out. Place your dish in the cooking
compartment.
Notes
■ If a cooking time has been set, this runs
independently of the rapid heat up process and
counts down immediately when operation is started.
■ You can use the l button to check the current
cooking compartment temperature during rapid heat
up.
Cancelling
Press the c button. The c symbol disappears from
the display.
OTime-setting options
Ti me- set t i ng opt i ons
Your appliance has different time-setting options.
Notes
■ A cooking time of up to one hour can be set exactly
to the minute.
A cooking time of over one hour can be set in 5-
minute increments.
■ Depending on which direction you turn the rotary
selector, the cooking time starts at a default value:
Anti-clockwise, 10 minutes,
Clockwise, 30 minutes.
■ After a time-setting option has elapsed, a signal
sounds.
■ Using the l button, you can request information
during operation, which then appears briefly in the
display.
Timer
You can set the timer at any time, even if the appliance
is switched off. It runs parallel to the other time settings
and has a separate audible signal. In this way, you can
tell whether it is the timer or a cooking time which has
elapsed.
The maximum setting you can apply is 24 hours.
1. Press the 0 button.
The field for the timer opens.
2. Use the rotary selector to set the timer duration.
The timer starts after a few seconds.
The
U symbol for the timer and the time counting down
are displayed on the left in the status bar.
When the time has elapsed
An audible signal sounds. "Timer elapsed" appears in
the display. Use the 0 button to cancel the audible
signal early.
Cancelling the timer duration
Press the 0 button to open the time-setting options
menu and turn the time back. Press the 0 button to
close the menu.
Changing the timer duration
Use the 0 button to open the time-setting options
menu and change the timer time in the next few
seconds using the rotary selector. Start the timer with
the 0 button.
Cooking time
If you set the cooking time for your food, operation
stops automatically once this time has elapsed. The
oven stops heating.
Prerequisite: A type of heating and a temperature have
been set.
For example: Setting for 4D hot air, 180 °C, cooking
time 45 minutes.
1. Press the 0 button.
The time-setting options menu opens.
2. Set the cooking time using the rotary selector.
3. Press the Start/Stop button to start.
You can see the cooking time x counting down in
the status bar.
The cooking time has elapsed
A signal sounds. The oven stops heating. You can
cancel the audible signal early using the 0 button.
Cancelling the cooking time
Press the 0 button to open the time-setting options
menu. Turn the time back. The type of heating and
temperature set are shown in the display.
Changing the cooking time
Press the 0 button to open the time-setting options
menu. Change the cooking time using the rotary
selector.
Time-setting option Use
Q
Timer The timer functions like an egg timer. An
audible signal sounds once the set time
has elapsed.
+
Cooking time A signal sounds once a set cooking time
has elapsed. The appliance switches off
automatically.
*
End Set a cooking time and an end time. The
appliance switches on automatically so
that the operation ends at the desired
time.
PLQV
ꑘ
PLQV
ꑖ 'XUDWLRQ
7LPHU
PLQV
ꑘ
PLQV
ꑖ 'XUDWLRQ
7LPHU
Childproof lock en
15
End time
If you change the end time, please remember that
easily spoiled foods must not be allowed to remain in
the cooking compartment for too long.
Prerequisite: The selected operation has not already
begun. A cooking time has been set. The time-setting
options menu
0 is open.
Example in the picture: You put the dish in the cooking
compartment at 9:30. It takes 45 minutes to cook and
will be ready at 10:15, but you would like it to be ready
at 12:45 instead.
1. Touch the ¿ arrow to continue to "y end".
2. Set the end time using the rotary selector.
3. Confirm with the Start/Stop button.
The oven is in standby. The
y symbol and the time at
which the operation will be finished appear in the status
bar. The operation starts at the appropriate time. You
can see the cooking time counting down in the status
bar.
The cooking time has elapsed
A signal sounds. The oven stops heating. You can
cancel the audible signal early using the 0 button.
Correcting the end time
This is possible if the oven is in standby.
1. Press the Start/Stop button.
2. Press the 0 button.
The Time-setting Options menu opens.
3. Use the ¿ arrow to switch to "y End" and correct
the end time using the rotary selector.
4. Press the 0 button.
5. Press the Start/Stop button.
The oven is on standby.
Cancelling the end time
This is possible if the oven is in standby.
1. Press the Start/Stop button.
2. Press the 0 button.
The Time-setting Options menu opens.
3. Use the ¿ arrow to switch to "y End" and turn the
end time back using the rotary selector.
4. Press the 0 button.
5. Press the Start/Stop button to start.
The cooking time starts to count down immediately.
AChildproof lock
Chi l dpr oof l ock
Your appliance is equipped with a childproof lock so
that children cannot switch it on accidentally or change
any settings.
Activating and deactivating
You can activate and deactivate the childproof lock
when the appliance is switched on or off.
In each case, press the
/ button for approx. 4
seconds. A confirmation note appears in the display
and the / symbol appears in the status bar.
The appliance door is locked
In the basic settings, you can change the settings so
that the appliance door is also locked in addition to the
control panel.
The appliance door locks if the temperature in the
cooking compartment reaches approx. 50 °C. The
H
symbol is displayed in the status bar. When the oven is
switched off, the appliance door locks immediately if the
childproof lock has been activated.
QBasic settings
Ba s i c set t i ngs
There are various settings available to you in order to
help use your appliance effectively and simply. You can
change these settings as required.
Changing settings
1. Press the "On/off" button.
2. Press the menu button.
The operating modes menu opens.
3. Use the rotary selector to select "Settings".
4. Touch the arrow ¿.
5. Use the rotary selector to change the values.
6. Use the arrow ¿ to change to the next settings, and
change them if necessary.
7. Press the menu button to save.
"Save" or "Discard" appears on the display.
List of settings
This list tells you all the basic settings and how to
change them. Depending on the model of the appliance
you own, the display will show only those settings that
apply to your appliance.
You can change the following settings:
ꑗ
(QG
&
ꑗ
'KRWDLU
Setting Options
Select language Additional languages possible
Time of day Sets the current time
Date Sets the current date
To Next Page
Loading...
