EasyManuals Logo

Siemens HS736G3 1 Series User Manual

Siemens HS736G3 1 Series
56 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #15 background imageLoading...
Page #15 background image
Rapid heating en
15
Note:If you open the appliance door during operation,
the appliance stops heating. When you close the appli-
ance door, the appliance continues to heat again. To
ensure that the behaviour of the appliance is not
changed during operation, only open the appliance
door once the set time has elapsed.
1.
Change the "Lighting" basic setting to "Always off".
→"Basic settings", Page24
2.
Change the "Standby screen" basic setting to "On".
3.
Change the "Signal tone" basic setting to "Very short
duration".
This ensures that the light in the cooking compart-
ment is always off while the appliance is operating
and when you open the appliance door, and the
time display does not change. The duration of the
signal tone is reduced at the end of the operation.
4.
Set the required operating mode.
→"Setting an operating mode", Page14
→"Setting the type of heating and the temperature",
Page14
5.
Set the required cooking time depending on the op-
erating mode.
→"Setting the cooking time", Page15
→"Time-setting options", Page15
6.
Use "End time" to set the time at which the opera-
tion should end.
→"Setting the end time", Page16
→"Time-setting options", Page15
7.
Place the food in the cooking compartment before
the appliance starts to heat.
8.
Start the operation.
a The display shows the time remaining until the oper-
ation starts. The appliance is in standby mode.
a Once the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down.
9.
When the operation has ended, remove the food
from the cooking compartment. The appliance auto-
matically switches off completely after approximately
15 to 20minutes.
Note:If required, change the different basic settings
again.
Rapid heating
9  Rapid heating
To save time, rapid heating can shorten the preheat-
ing time for set temperatures over 100°C.
Rapid heating is possible for the following types of
heating:
¡ 4Dhot air
¡ Top/bottom heating
9.1 Setting rapid heating
To ensure an even cooking result, do not place the
food in the cooking compartment until rapid heating
has come to an end.
Note:Do not set a cooking time until rapid heating has
come to an end.
1.
Set a suitable type of heating and a temperature of
at least 100°C.
Rapid heating automatically switches on at temper-
atures of 200°C and above.
2.
Press "Rapid heating".
a "On" is in the tile.
3.
Press to start the operation.
a Rapid heating starts.
a Once rapid heating has ended, a signal sounds.
"Off" appears for "Rapid heating" ⁠.
4.
Place the food in the cooking compartment.
Cancelling rapid heating
Press "Rapid heating".
a For "Rapid heating" "Off" appears on the display.
Time-setting options
10  Time-setting options
For an operation, you can set the cooking time and the
time at which the operation should be finished. The
timer runs independently of the operation.
Time-setting
option
Use
Cooking time If you set a cooking time, the appli-
ance stops heating automatically
once this time has elapsed.
End time Along with the cooking time, you can
set the time at which you want the
operation to end. The appliance
starts up automatically so that the
operation finishes at the required
time.
Timer You can set the timer to run inde-
pendently of the appliance during op-
eration. It does not affect the appli-
ance.
10.1 Setting the cooking time
You can set the cooking time for the operation of up to
24 hours.
Requirement:An operating mode and temperature or
setting have been set.
1.
Press "Cooking time".
2.
To set the cooking time, press the relevant time
value, e.g. hour display "h" or minute display "min."
a The selected value is marked in blue.
3.
Set the cooking time using or or via the adjust-
ment bar. Or enter the cooking time directly via the
number field ⁠.
If required, use to reset the adjustment value.
4.
Press "Apply".
5.
Use to start the operation.
a The appliance starts to heat and the time counts
down.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens HS736G3 1 Series and is the answer not in the manual?

Siemens HS736G3 1 Series Specifications

General IconGeneral
BrandSiemens
ModelHS736G3 1 Series
CategoryOven
LanguageEnglish

Related product manuals