EasyManuals Logo

Siemens SINUMERIK 840D sl Series User Manual

Siemens SINUMERIK 840D sl Series
1002 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #46 background imageLoading...
Page #46 background image
Overview of Alarms 08/2005
2-46
© Siemens AG, 2005. All rights reserved
SINUMERIK 840D sl/840D/840Di/810D Diagnostics Guide (DA), 08/2005 Edition
for channel synchronization in ISO2/3 mode or the machine data
$MN_EXTERN_CHAN_SYNC_M_NR_MAX is smaller than
$MN_EXTERN_CHAN_SYNC_M_NR_MIN.
Reactions: - Mode group not ready.
- Channel not ready.
- NC Start disable in this channel.
- Interface signals are set.
- Alarm display.
- NC Stop on alarm.
Remedy: Check machine data $MN_EXTERN_CHAN_SYNC_M_NR_MIN and
$MN_EXTERN_CHAN_SYNC_M_NR_MAX.
Program Con-
tinuation:
Switch control OFF - ON.
4180 Invalid M function number assigned to enable ASUP
Definitions: An invalid M function number has been assigned for activation of ASUP. An illegal M
number has been assigned in machine data $MN_EXTERN_M_NO_SET_INT or
$MN_EXTERN_M_NO_DISABLE_INT for the configuration of the M number range for
activation/deactivation of the interrupt program.
Reactions: - Mode group not ready.
- Channel not ready.
- NC Start disable in this channel.
- Interface signals are set.
- Alarm display.
- NC Stop on alarm.
Remedy: Check machine data $MN_EXTERN_ M_NO_SET_INT and
$MN_EXTERN_M_NO_DISABLE_INT.
Program Con-
tinuation:
Switch control OFF - ON.
4181 Channel %1 invalid assignment of an M auxiliary function number
Parameters: %1 = Channel number
Definitions: In machine data $MC_AUXFU_ASSOC_M0_VALUE or
$MC_AUXFU_ASSOC_M1_VALUE, a number has been specified for the configuration of
a new predefined M function which is occupied by the system, and cannot be used for an
assignment. (M0 to M5, M17, M30, M40 to M45).
Reactions: - Mode group not ready.
- Channel not ready.
- NC Start disable in this channel.
- Interface signals are set.
- Alarm display.
- NC Stop on alarm.
Remedy: Configure an M function in machine data $MC_AUXFU_ASSOC_M0_VALUE or
$MC_AUXFU_ASSOC_M1_VALUE which is not occupied by the system (M1 to M5, M17,
M30, M40 to M45).
Program Con-
tinuation:
Switch control OFF - ON.
4182 Channel %1 invalid M auxiliary function number in %2%3, MD reset
Parameters: %1 = Channel number
%2 = MD identifier
%3 = If required, MD index

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Siemens SINUMERIK 840D sl Series and is the answer not in the manual?

Siemens SINUMERIK 840D sl Series Specifications

General IconGeneral
Control TypeCNC
PLCIntegrated SIMATIC S7-300
InterfacesEthernet, PROFIBUS, PROFINET, USB
Max Axes31
Programming LanguagesDIN/ISO 66025, high-level language (C/C++), Siemens programming languages (e.g., ShopMill, ShopTurn)
Safety FeaturesIntegrated safety functions (Safety Integrated)
Operating SystemWindows-based
Drive InterfaceSINAMICS S120
ApplicationsMilling, turning, grinding, laser
DisplayTFT color display, various sizes

Related product manuals