Siemens SINUMERIK 880 GA2

11.92 9 Examples
9.1.6 Display "Magazine assignment"
9.1.6 Display "Magazine assignment"
DISPLAY
T. DATA
CHANGE
T. DATA
TOOL
SELECT.
HELP
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
Assignment Magazine: 1
a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a
AUTOMATIC
a a a a a a a a
a
a a a a a a
a
a
a a a a a a
a
a a a a a a a a
1.1
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a a a a a
a
a a a
a
a
a a a
a
a a a a a
T No. Duplo. Size Status
VGENFB
1234
E B
1
1
11
Location
10000000
V B
1
2
11
7523
E B
1
3
11
4711
VG B
1
4
11
5678
B
2
5
11
9876
V B
2
6
11
1
B
1
7
11
Softkey "DISPLAY T. DATA"
Provides all the relevant data for the selected tool by evaluating the cursor line position.
The data cannot be modified.
After a recall from magazine assignment, the cursor is positioned on the previously selected
line of the table.
The display cannot be selected for fictitious magazines. A message is output.
Softkey "CHANGE T. DATA"
Provides all the relevant data for the selected tool by evaluating the cursor line position.
The data of all P memories can be modified.
After a recall from magazine assignment, the cursor is positioned on the previously selected
line of the table.
The display cannot be selected for fictitious magazines. A message is output.
Softkey "TOOL SELECT."
Provides a list of all tools in all magazines and in the buffer which are selected via the criterion
of the cursor column.
After a recall from the magazine assignment, the cursor is positioned on the previously
selected line of the table.
The tool selection buffer is limited to 50 tools.
Softkey "HELP"
Provides a description of the abbreviations used in the display.
© Siemens AG 1991 All Rights Reserved 6FC5 197-0AA40-1BP1 9–7
SINUMERIK 840/880 (PJ)