Siemens SINUMERIK 880 GA2

11.92 9 Examples
9.1.14 Display "Loading/unloading spindle"
9.1.14 Display "Loading/unloading spindle"
LOAD UNLOAD
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
Loading/unloading spindle:
a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a
a
AUTOMATIC
a a a a a a a a
a
a a a a a a
a
a a a a a a a a
1.1
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
L1:
L2:
R:
Spec. tool life:
1
1200
11
743
750
2000
Spec. tool life:
T No.:
Size:
1
Duplo No.:
Prewarning limit tool life:
Geometry:
2
1
Type:
Cutting edge No.:
100
Wear:
L1:
L2:
R:
0.005
0.002
0.001
Softkey "LOAD"
Provides the display "Loading spindle". A check is made whether the spindle is assigned. If
not, a search for an empty location is initiated. The tool size entered in the loading line is
referred to when searching for a location of suitable size. The search for an empty location
only covers the loading magazine (defined in the machine data, currently DW 136 of DB 146).
The empty location found is reserved for the tool change. The control bit "Load location" is
output at the interface (signals to user DW 2...DW 5 in DB 146). If no empty location is found,
the process must be aborted.
Softkey "UNLOAD"
Transfers the display "Unloading spindle", after entry of the T No. and Duplo No., to the
loading line. The data of the tool to be unloaded are displayed. The control bit "Unload
location" is output at the interface (signals to user DW 2...DW 5 in DB 146).
© Siemens AG 1991 All Rights Reserved 6FC5 197-0AA40-1BP1 9–15
SINUMERIK 840/880 (PJ)