Siemens SINUMERIK 880 GA2

5 Configuring 01.91
5.7 FB 122 Search for empty location with presetting
Possible parameter assignments
Parameter assignments of the search area
MAGA
> 0
MAGE
>=MAGA
= 0
a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a
Search area
parameters
Magazine
MAGA-MAGE
(2)
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
VRS
X X (1)
X X (1)
from/to
1 - end
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a
Specified search area
a a a a a a a a a a a a a a a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a
a a a a a a a a a a a a a
a
a a a a a a a a a a a a a a a
Spec. search
direction
(1) The search direction "Symmetrical" is only permissible for linear magazines
(MD bit 10 = 1). For non-linear magazines, the search direction "Forwards" is defined
internally.
(2) With the parameter assignments "MAGA" > 0 and "MAGE" = 0, all chained magazines
are searched, starting at "MAGA". The search operation is not terminated until
– the required empty location has been found,
– the searched magazine is not assigned to any further, chained magazine,
– the chained magazine corresponds to the magazine specified in the parameter
"MAGA".
Note that all magazines included in the search key must have the same
machine data setting (with configuration) if the search for an empty
location extends over several magazines.
5–26 © Siemens AG 1991 All Rights Reserved 6FC5 197-0AA40-1BP1
SINUMERIK 840/880 (PJ)