What does 'Drift detected, ground voltage offset to terminal 3' mean on my Siemens Temperature Controller?
If your Siemens Temperature Controller displays 'Drift detected, ground voltage offset to terminal 3', it means a critical measurement error is detected on ground voltage offset to terminal 3. Reconnect or repair the sensor. If the problem persists, contact Technical Support.
Why does my Siemens Temperature Controller display 'No symbol is displayed' after a configuration change?
If your Siemens Temperature Controller displays 'No symbol is displayed' and the device configuration has changed due to a work process, reset the configuration bit memory to delete the diagnostic message.
Why does my Siemens Temperature Controller display 'No symbol is displayed' when the device state is ok?
If your Siemens Temperature Controller displays 'No symbol is displayed' and the device state is ok with no errors from active diagnostics, no action is required.
Why does my Siemens Temperature Controller show 'Configuration not supported by device'?
If your Siemens Temperature Controller displays 'Configuration not supported by device' because the configuration is temporarily invalid for less than 3 seconds, for example, during parameter download, no further action is required.
What to do if Siemens SITRANS TS500 Temperature Controller shows electronics defect?
If your Siemens Temperature Controller displays 'Electronics defect', a replacement of the device is recommended. Contact Technical Support.
How to fix 'CRC16 error in input CPU configuration' on Siemens Temperature Controller?
If your Siemens Temperature Controller displays 'CRC16 error in input CPU configuration', reset the device or switch it off and back on.
Why is 'Backup enabled' on my Siemens SITRANS TS500 Temperature Controller?
If your Siemens Temperature Controller displays 'Backup enabled', it means a sensor error is detected, and the backup sensor is in use. Unplug and reconnect the sensor cable. Check if the sensor is operated out of specified limits. If the problem persists, replace the sensor.
What does 'Backup error' mean on my Siemens SITRANS TS500?
If your Siemens Temperature Controller displays 'Backup error', it means a sensor error is detected at the backup sensor, and no backup is available. Unplug and reconnect the sensor cable. Check if the sensor is operated out of specified limits. If the problem persists, replace the sensor.
How to fix 'Exception error during code execution' on Siemens Temperature Controller?
If your Siemens Temperature Controller displays 'Exception error during code execution', reset the device or switch it off and back on.
What does 'Primary variable out of limits' mean on my Siemens SITRANS TS500 Temperature Controller?
If your Siemens Temperature Controller displays 'Primary variable out of limits', it means the process value has reached the sensor limit. Review process conditions versus product specifications.
Instructions on how to modify parameter values via the device display.
Methods to protect device settings from unauthorized changes.
Procedure to enable write protection using the physical switch.
Lists and groups parameters accessible via local or remote operation.
Steps for assigning parameters using the USB modem and software.
Detailed parameter configuration using the device's local display.
Procedure to change the user PIN for device security.
Enables or disables the user PIN for parameter access control.
Configuring parameters remotely via software tools.
Guides for calibrating the sensor using one or two points.
Configuration of output current settings, including fault currents.
Procedure to set the transmitter fault current via a switch.
Critical safety warnings for maintenance and repair tasks.
Recommendations for recalibration intervals and conditions.
Lists diagnostic message IDs, causes, and recommended actions.
Ambient temperature limits for gas hazardous areas.
Ambient temperature limits for flameproof enclosures.
Ambient temperature limits for dust hazardous areas.
Overview of SIMATIC PDM software for device management.
General| Type | Temperature Transmitter |
|---|---|
| Housing Material | Aluminum |
| Display | LCD |
| Accuracy | ±0.1 °C |
| Output Signal | 4-20 mA |
| Communication | HART |
| Input | RTD, Thermocouple |
| Operating Temperature | -40 to 85 °C |
| Ambient Temperature | -40 to 85 °C |
| Mounting | DIN rail mounted |
| Protection Class | IP66 |
To Next Page
