Silverline 262212 - User Manual

Other manuals for Silverline 262212

Manual40 pages

Questions and Answers

K
kristin23Aug 2, 2025
Why Silverline Power Tool drill press will not start?
- K
  Karen ScottAug 2, 2025
  If the Silverline Power Tool drill press won't start, first ensure the mains plug is fully inserted into the socket and the socket is switched on. Also, check if the RCD is fitted and reset/on. Then, check the fuse in the mains plug and replace it if necessary with the same value. Make sure the Pulley Cover is fully closed and securely fastened, and check the safety switch mechanism inside the Pulley Cover for damage. If these steps don't resolve the issue, the On/Off Switch may be faulty, and you should contact your Silverline dealer or an authorized service center.
K
kingjackAug 8, 2025
What to do if Silverline Power Tool drill bit smoking and excessive heat?
- D
  dawn33Aug 8, 2025
  If the Silverline Power Tool drill bit is smoking and there's excessive heat, the speed setting might be incorrect, so change the speed. The drill bit may also be blunt, so replace or sharpen it. Additionally, the material or drill bit may need lubrication; use lubricant or cutting fluid.
S
Sheila DyerAug 13, 2025
Why Silverline Power Tool has abnormal or high levels of operating noise?
- W
  William ParrishAug 13, 2025
  Abnormal noise in your Silverline Power Tool can be due to several reasons. The belt tension might be incorrect, so adjust the tension. The spindle may need lubricating; apply grease to the internal spindle between the Chuck and Spindle Pulley. Check the body of the tool and inside the Pulley Cover to ensure all parts are secure and correctly fitted. If the pulley drive belt is worn or damaged, it should be replaced. Contact your Silverline dealer or www.toolsparesonline.com for a replacement belt.
S
Steven StephensAug 20, 2025
How to fix Silverline 262212 drill bit wobble or run out?
- B
  Brandon SmithAug 20, 2025
  If the Silverline Power Tool drill bit wobbles, it could be due to a bent drill bit, so replace it. It could also be because the drill bit is not centrally located in the Chuck, so refit the drill bit in the chuck. If these steps don't resolve the issue, contact your Silverline dealer or an authorised service centre.
J
Jeffery DoughertyAug 26, 2025
What to do if Silverline 262212 drill bit binds in workpiece?
- C
  Cheryl JacksonAug 26, 2025
  If the Silverline Power Tool drill bit binds in the workpiece, the pulley belt may have incorrect low tension. Adjust the tension.

Summary

Description of Symbols

Product Specification

Environmental Protection Information

General Power Tool Safety Warnings

Additional Safety for Bench or Stationary Drills

Specific safety instructions for bench or stationary drills, including protective equipment and safe operation procedures.

Product Familiarisation

Intended Use of Drill Press

Details the intended application of the bench mounted vertical drill for various materials.

Unpacking and Assembling Your Drill Press

Instructions for unpacking, checking parts, and assembling the drill press components.

Adjusting Drill Press Speed Settings

Guidance on how to adjust the drive belt tension to select one of the five available speeds.

Operating Your Drill Press

Using Plunge Handles and Chuck

Instructions on using plunge handles for feeding and operating the chuck for securing drill bits.

Table Adjustment and Drilling Depth

How to adjust the table position, tilt, and set the drilling depth for accurate work.

Drilling Procedures for Wood and Metal

Specific advice for drilling wood and metal, including bit selection and safety precautions.

Troubleshooting Common Issues

Silverline Tools Guarantee and Terms

Registering Your Product for Guarantee

Details on how to register the product online within 30 days to activate the 3-year guarantee.

Guarantee Terms and Conditions

Explains what is covered, what is not covered, and procedures for making a claim.

CE Declaration of Conformity

Statement confirming the product conforms to relevant EU directives and standards.

Silverline 262212 Specifications

General

Chuck type	-
Product type	Bench drill press
On/off switch	Yes
Product color	Black, Blue
Noise level	86 dB
Throat depth	104 mm
Number of speeds	5
Rotational speed (max)	2600 RPM
Rotational speed (min)	600 RPM
Drill bit diameter (max)	13 mm
Drill bit diameter (min)	1.5 mm
Drill table tilting	-45 - 45 °
Drill table size (WxD)	160 x 160 mm
AC input voltage	230 V
AC input frequency	50 Hz