Simoniz 039-8065-8 - User Manual

Questions and Answers

S
shawjamesAug 17, 2025
Why won't my Simoniz 039-8065-8 Pressure Washer motor start?
- O
  orossAug 17, 2025
  If the motor of your Simoniz Pressure Washer doesn't start, there could be several reasons. First, ensure the device is in ON mode by pushing the ON/OFF button. Then, check if the power cord is properly plugged in. Also, the extension cord might be too long, not the proper gauge, or damaged; replace it with a 25’ (7.6 m) or 50’ (15 m) 14/3 gauge cord. The power outlet might not supply enough power, so try a different outlet. Finally, the pressure washer circuit breaker might have tripped; allow the device to cool, and then restart it.
J
Jim WilsonAug 20, 2025
Why does my Simoniz 039-8065-8 motor hum but not run?
- C
  Cynthia BarnesAug 20, 2025
  If your Simoniz Pressure Washer motor hums but fails to run, consider these potential causes: The supply voltage may be below the minimum; verify that only the pressure washer is running on this circuit. The system might have residual pressure; turn the device to OFF mode, pull the trigger on the spray gun to release pressure, and then turn the device back ON. Voltage loss due to the extension cord could also be a factor; unplug any extension cords and plug the unit directly into the outlet. There might be residual friction among components; disconnect the water supply and power ON for 2 to 3 seconds, repeating this procedure a few times until the motor starts.
T
timothyporterAug 23, 2025
How to fix detergent not working on Simoniz 039-8065-8 Pressure Washer?
- T
  Tyler HooperAug 23, 2025
  If the detergent is not working on your Simoniz Pressure Washer, consider these possible causes: the detergent container might be empty, so add more detergent. Check the detergent bottle or suction tube connections to ensure they are properly connected. If the detergent is too thick, dilute it. Also, the filter on the detergent suction tube might be clogged; run warm water through it to remove any build-up. A damaged or clogged detergent suction tube can also be the reason; remove any obstruction or replace the tube. Finally, make sure that the ON/OFF button is in the ON mode.
K
Kathleen GreeneAug 26, 2025
How to fix a leaking garden hose connection on Simoniz 039-8065-8?
- K
  Katie LaneAug 26, 2025
  If the garden hose connection on your Simoniz Pressure Washer is leaking, it could be due to loose fittings; tighten them. Also, check for a missing or worn rubber washer and insert a new one if necessary.
E
Erin JohnsonAug 28, 2025
What to do if my Simoniz Pressure Washer doesn't reach high pressure?
- B
  Brittany WilsonAug 28, 2025
  If your Simoniz Pressure Washer isn't reaching high pressures, several factors could be the cause. The garden hose might be too small; replace it with a 1” (25 mm) or 5/8” (16 mm) garden hose. A restricted water supply could also be the issue; check the garden hose for kinks, leaks, or blockages. Ensure you have enough water supply by fully opening the water source. A clogged water inlet filter can also reduce pressure; remove the filter and rinse it with warm water. Lastly, the power nozzle might be in the low-pressure position; replace it with the desired high-pressure tip.
C
Christopher CarrAug 31, 2025
Why does the output pressure fluctuate on my Simoniz 039-8065-8 Pressure Washer?
- N
  Nathaniel LewisAug 31, 2025
  If the output pressure of your Simoniz Pressure Washer fluctuates, it could be due to several reasons. Ensure there's enough inlet water supply by turning the faucet on fully and checking the garden hose for kinks, leaks, or blockages. The pump might be sucking air; check if all hoses and fittings are airtight, then turn the device OFF and purge the pump by pulling the trigger on the spray gun until a steady flow of water emerges through the nozzle. A clogged water inlet filter can also cause pressure fluctuations; remove the filter and rinse it with warm water. Additionally, the discharge nozzle might be obstructed; blow out or remove debris with a fine needle. Finally, the gun, hose, or power nozzle might be calcified; run distilled vinegar through the detergent container.
L
lisa93Sep 2, 2025
Why is the pump on my Simoniz 039-8065-8 Pressure Washer so noisy?
- J
  Jason DelgadoSep 3, 2025
  A noisy pump in your Simoniz Pressure Washer can be attributed to a couple of reasons. The pump might be sucking air; check if all hoses and fittings are airtight, then turn the device to OFF mode and purge the pump by pulling the trigger on the spray gun until a steady flow of water emerges through the nozzle. Alternatively, the water filter could be clogged; remove the filter and rinse it with warm water.
J
jeffrey53Sep 5, 2025
Why is no water coming out of the Simoniz 039-8065-8 Pressure Washer nozzle?
- L
  lauren73Sep 5, 2025
  If no water is coming out of the nozzle of your Simoniz Pressure Washer, the water supply might be OFF; turn on the water supply. Alternatively, there might be a kink in the garden hose; remove the kink.
M
Morgan ColemanSep 8, 2025
Why is my Simoniz 039-8065-8 Pressure Washer spray wand leaking?
- S
  swarrenSep 8, 2025
  If your Simoniz Pressure Washer spray wand, extension, or nozzle is leaking, it could be because the spray nozzle was not properly attached; ensure the quick-connect wand is attached securely and the project dial is clicked in securely. If there is a broken O-ring or plastic insert: Call the Toll-free Hotline.
D
Douglas NicholsonSep 12, 2025
Why is my Simoniz 039-8065-8 Pressure Washer pump leaking water?
- C
  Craig TuckerSep 12, 2025
  If your Simoniz Pressure Washer pump is leaking water, ensure all fittings are tight. If the water seals are damaged or worn: Call the Toll-free Hotline.