SimPure Membrane Solutions MS18

Need help?

Do you have a question about the SimPure Membrane Solutions MS18 and is the answer not in the manual?

Summary

Getting Started

Introduction to MS18 Air Purifier

Welcome to the MS18 Air Purifier, providing clean air for home or office.

Health and Safety Precautions

Essential safety guidelines and warnings for operating the air purifier safely.

Operating Guidelines and Parameters

Details the operating parameters, specifications, and performance data of the air purifier.

Installation Guide

System Contents and Components

Lists and illustrates all the parts included with the MS18 Air Purifier.

Commissioning the Air Purifier System

Step-by-step instructions for initial setup and powering on the air purifier.

Operation Guide

Control Panel Overview

Explains the layout and functions of the air purifier's control panel.

Power and Fan Speed Controls

Instructions for using the power button and adjusting fan speed.

Special Modes and Features

Details on Sleep Mode, Timer function, and Night Light.

Filter Reset Procedure

How to reset the filter indicator after a filter replacement.

Filter Replacement

Filter Replacement Steps

Detailed instructions on how to remove the old filter and install a new one.

Replacement Filter Part Number

Identifies the part number for the single composite filter element.

Troubleshooting Guide

Common Air Purifier Problems and Solutions

Addresses issues like not turning on, reduced airflow, and unusual noise.

Filter Indicator and Other Issues

Solutions for filter indicator lights, sleep mode operation, and unlisted problems.

The MS18 Air Purifier is designed to deliver clean and healthy air for your home or office environment. This owner's handbook outlines the installation, operation, and maintenance requirements to sustain optimal product performance. The device is intended for indoor use only and should be installed on a flat, level, dry, and secure surface with average ambient room temperature, away from direct sunlight. It is crucial to keep the device away from flammable gas appliances such as heaters or fireplaces and to avoid using it in places with heavy moisture or smoke.

Function Description

The MS18 Air Purifier is equipped with a primary filter that includes Activated Carbon and an H11 High-Efficiency Particulate Air (HEPA) filter. This filtration system is highly effective, capturing over 99.97% of particles with a diameter greater than or equal to 0.3 microns. The device is capable of filtering out a wide range of airborne impurities and particles, including viruses, mold, dust, allergens, pollen, bacteria, dust mites, cigarette smoke, pet dander, off-odors, and unhealthy vapors. This comprehensive filtration ensures a significant improvement in air quality, contributing to a healthier living or working space.

Usage Features

The MS18 Air Purifier offers several user-friendly features for convenient operation:

Power Control: The device is turned on by pressing the power button once, which puts it into operating mode. A second press of the power button will stop the air purifier and place it into standby mode.
Fan Speed Settings: The fan speed can be adjusted by repeatedly pressing the "SPEED" button. There are three distinct speed settings:
- 1/Sleep: This is the lowest speed setting, designed for quiet operation.
- 2: This represents a medium speed setting.
- 3: This is the high-speed setting for maximum air purification. The corresponding fan speed indicator light on the control panel will illuminate to show the current fan speed.
Sleep Mode: To activate sleep mode, press the "SLEEP" button. In this mode, the fan operates at its lowest and quietest setting. Additionally, only the Sleep and Power buttons remain illuminated, helping to maintain a dark room environment, ideal for nighttime use.
Timer Function: The air purifier includes a timed auto-off feature. After powering on the device, press the "TIME" button repeatedly to cycle through preset auto-off times of 2, 4, or 8 hours. The corresponding indicator light will display the selected auto-off time setting, allowing users to schedule operation and conserve energy.
Night Light: The device features a night light function. Press the "NIGHT LIGHT" button once to turn on the night light. Pressing it a second time will turn off the night light.

Maintenance Features

Proper maintenance is essential for the longevity and optimal performance of the MS18 Air Purifier. Key maintenance features include:

Filter Replacement Indicator: The air purifier is equipped with a filter indicator lamp that illuminates when the total run hours reach 1000 hours, signaling that the filter needs replacement.
Filter Reset Function: After replacing the filter, the filter timer function must be reset. This is done by pressing and holding the filter reset button for 3 seconds until the indicator light turns off. This ensures accurate tracking of the new filter's lifespan.
Filter Replacement Procedure:
1. Preparation: Turn off the air purifier and unplug the power cord from the electrical outlet.
2. Removal of Old Filter: Open the rear cover of the air purifier and remove the exhausted composite filter element. It is crucial to ensure that any packaging from the filter element is removed before initial use, as the product will not function correctly otherwise.
3. Cleaning: Clean out any remaining dust, dirt, or lint inside the purifier using a vacuum hose or a dry cloth. DO NOT use water or liquids to clean the purifier.
4. Installation of New Filter: Remove any packing from the new filter element. Pay attention to the inward and outward sides of the filter element, referring to the new filter instructions for the correct direction of airflow. Place the new filter into the air purifier, ensuring it is facing the correct direction (airflow travels from outside to the center of the unit).
5. Reassembly and Reset: Reinstall the rear cover. Plug the power cord back into an electrical outlet. Then, press and hold the filter button for 3 seconds to reset the filter timer. The indicator light will go out, confirming a successful reset.
Cleaning the Device: Regularly clean the device and remove any dust from the power plug. Always unplug the unit when cleaning. Avoid using strong corrosive detergents or chemicals, as they may damage the surface of the device.
Filter Obstruction: Do not obstruct the air inlets or outlets on the device.
Filter Reuse: The composite filter should not be washed or reused; it must be replaced with a new filter when exhausted.

The actual lifespan of the filter may vary depending on environmental factors such as the amount of dust, smoke, humidity, and the concentration of other airborne particles and vapors present in the air. For filter replacement options or any other customer service inquiries, users are encouraged to contact Membrane Solutions via their service email or toll-free phone number.

SimPure Membrane Solutions MS18 Specifications

General

Product Type	Air Purifier
HEPA Filter Grade	H13
Pre-filter	Yes
Activated Carbon Filter	Yes
UV-C Light	No
Warranty	1 year
Filtration Technology	HEPA, Activated Carbon
Ozone Output	0 ppm
Control Type	Touch Control
Timer	Yes