How to troubleshoot if the Smeg GW1260 Laboratory Equipment program does not start?
If the Smeg Laboratory Equipment program isn't starting, make sure the device is connected to the electrical mains, there is no power outage, the water intake taps are turned on, and the device door is properly closed.
Why are items not cleaned properly in my Smeg GW1260 Laboratory Equipment?
If items aren't cleaned properly in your Smeg Laboratory Equipment, ensure you're using the correct amount of detergent, instruments are positioned correctly, the selected program suits the dirt type and degree, all filters are clean and correctly installed, spray arm water outlets aren't clogged, nothing obstructs spray arm rotation, and the salt container cap is properly closed.
What to do if items fail to dry or are dull in Smeg GW1260 Laboratory Equipment?
If items in your Smeg Laboratory Equipment aren't drying or appear dull, check the absolute drying filter condition, ensure there's neutralising agent in the container with correct dispensing settings, and verify the detergent is of good quality and effective.
Why are there traces of rust in the Smeg GW1260 chamber?
If you notice rust traces in the chamber of your Smeg Laboratory Equipment, remember the chamber is made of corrosion-proof steel, so rust is likely from external factors. Use special rust removal products, ensure the detergent dose is correct (as some can be corrosive), and check the salt container cap is properly closed.
What to do if water stagnates in the chamber of Smeg GW1260 Laboratory Equipment?
If water stagnates in the chamber of the Smeg Laboratory Equipment, ensure the drain hose isn't kinked, the drain trap isn't blocked, and the washing chamber filters aren't clogged.
Why are the elements processed smeared and stained in Smeg GW1260?
If elements processed in your Smeg Laboratory Equipment are smeared or stained, ensure the rinse aid dispenser setting isn't too high and the salt container cap is properly closed.
How to fix the optional printer if it does not work with Smeg GW1260?
If the optional printer for your Smeg Laboratory Equipment isn't working, ensure the accessory is fitted with suitable thermal paper and the device is connected properly.
What to do if Smeg Laboratory Equipment interface is off or locked out?
If the Smeg Laboratory Equipment interface remains off or locked out, wait a few seconds for display card initialisation. If it persists, switch the device off using the main switch, wait 10 seconds, and switch it back on. If the display remains dead, contact after-sales service.
What to do if items in the load for washing are not cleaned properly in Smeg GW1260 Laboratory Equipment?
If the items in the load for washing are not cleaned properly in your Smeg Laboratory Equipment, ensure that you've added the correct amount of detergent, positioned the instruments correctly, and selected a suitable program for the type and degree of dirt. Also, verify that all filters are clean and correctly installed, the spray arm water outlet holes are not clogged, and nothing is obstructing the rotation of the spray arms. Finally, check that the salt container cap is properly closed.
Why do items in the load fail to dry or are dull in Smeg GW1260?
If the items in the load fail to dry or appear dull when using your Smeg Laboratory Equipment, check the condition of the absolute drying filter; its operating hours can be viewed as a device parameter. Ensure there is a neutralising agent in the container and its dispensing setting is correct. Also, verify the detergent is of good quality and hasn't lost its effectiveness due to incorrect storage.
Details the specific applications and intended use of the laboratory glassware washers.
Critical safety information, including load limits, handling, and potential hazards.
Explains how to interpret and respond to device alarms and failure notifications.
Step-by-step instructions for configuring the device's internal clock and date.
Steps for cleaning the device's filter system to maintain proper function and prevent clogs.
Essential information for the correct and safe electrical hookup of the laboratory washer.
Details the specific applications and intended use of the laboratory glassware washers.
Critical safety information, including load limits, handling, and potential hazards.
Explains how to interpret and respond to device alarms and failure notifications.
Step-by-step instructions for configuring the device's internal clock and date.
Steps for cleaning the device's filter system to maintain proper function and prevent clogs.
Essential information for the correct and safe electrical hookup of the laboratory washer.
General| Brand | Smeg |
|---|---|
| Model | GW1260 |
| Category | Laboratory Equipment |
| Language | English |
To Next Page
