Smiths Medical BCI SPECTRO2 30 User Manual

J
2009-07
WW1924-ADD7 REV 0
b
s
TM
Page 1 of 4
6 For use by or on the order of a licensed physician.
f Attention, see operation manual for additional instructions for use.
Quick Reference Guide
WW1030
BCI
®
Simplied Operation Guide
Pulse Oximetry Monitoring
Insert the sensor cable connector into the port located on top of the device.1.
Press the 2. On/O key (
x
) to turn the oximeter on.
Place the sensor on the monitoring site.3.
SpO4.
2
, pulse rate, pulse strength and Pulse amplitude Index (PI) bar will be displayed.
Pulse Volume
From monitoring mode, use Up/Down arrow keys (1.
n o
) to raise or lower pulse beep volume.
Continue to press the Down key to silence the pulse tone completely.2.
Silencing Alarms
Audible alarms can be silenced for two (2) minutes.1.
To silence the alarm tone, briey press the Alarm Silence key (2.
B
).
The Alarm Silence indicator will light solid for the rst minute and 45 seconds, then ash the last 15 seconds.3.
To cancel the 2-minute silence, briey press the Alarm Silence key (4.
B
).
NOTE: The Alarm Silence key will not aect visual alarm indicators or pulse tone.
Changing the Alarm Limits
To change the alarm limits, press the 1. Menu key ( ) until the desired parameter’s alarm limit is displayed.
Press the up or down key (2.
n o
) to increase or decrease the setting.
Press the 3. Menu key ( ) to advance to the next alarm limit.
To exit, press the 4. Exit key ( ) or wait 20 seconds until the patient reading is displayed.
Entering Setup Menu
Power oximeter on by pressing the 1. On/O key (
x
) located on the device’s upper right side.
When the patient number (Example: 2. P1) is displayed, press and hold the Exit key ( ) and then
press the Menu key ( ).
The Averaging Menu will be the rst option. 3. AVG will be displayed. Release the Exit key ( ).

Smiths Medical BCI SPECTRO2 30 Specifications

General

Measurement Parameters	SpO2, Pulse Rate, SpHb, PI, PVI
PVI Range	0 - 100%
Battery Life	Approximately 20 hours
Humidity	15% to 95% non-condensing
Display Type	Color LCD
Battery Type	4 AA batteries
Operating Temperature	5°C to 40°C
Storage Temperature	-20°C to 60°C
SpHb Range	0 - 25.0 g/dL
SpO2 Range	0-100%

Summary

Pulse Oximetry and Alarm Management

Pulse Oximetry Monitoring

Steps to monitor SpO2, pulse rate, and pulse strength using the oximeter.

Pulse Volume Adjustment

Instructions for adjusting the pulse beep volume or silencing it.

Silencing Audible Alarms

Procedure for temporarily silencing audible alarms for two minutes.

Changing Alarm Limits

Guide to adjusting the SpO2 and pulse rate alarm limits.

Entering Setup Menu

Steps to access the device's setup menu for configuration.

Device Settings and Configuration

Setting Averaging

How to select SpO2 averaging values (1-4) in the setup menu.

Setting Sensitivity

Instructions for turning High Sensitivity (HS) on or off.

Display Brightness Adjustment

Procedure to select display brightness level from 1 to 10.

Setting the Date

Steps to configure the year, month, and day settings.

Setting the Time

Guide to setting the hour and minute for the device.

Restoring Alarm Default Settings

How to restore all alarm limits to their factory default settings.

Advanced Operations and Maintenance

Device Operating Modes

Overview of the three operational modes: Clinician, Home, and Sleep.

Trend Interval Configuration

How to change the data recording interval for trend memory.

Remote Alarm Function

Instructions for activating or deactivating the remote alarm.

Restoring Factory Defaults

Steps to reset all device settings to their original factory defaults.

Clearing Trend Memory

Procedure to clear the oximeter's stored trend data.

Hardware and Accessories

Changing Batteries or Battery Pack

Guide to replacing the device's batteries or rechargeable battery pack.

Attaching the Sensor Cradle

Instructions for inserting sensor cradles for storage and protection.