Smoke hollow 105 - User Manual

Questions and Answers

D
Dr. Zachary HernandezAug 16, 2025
How to stop grease fire on Smoke hollow 105 Grill?
- S
  stephen95Aug 16, 2025
  To address a grease fire or excessive flames above the cooking surface of your Smoke hollow Grill, turn off the Regulator Knob and remove the LP Gas Cylinder. After the fire is out and the grill has cooled, clean any remaining food particles and excess grease from inside the firebox area, grease cup, and other surfaces. This is typically caused by too much grease build-up in the Burner section.
E
Emily RogersAug 21, 2025
How to prevent flare ups on Smoke hollow Grill?
- S
  susan36Aug 22, 2025
  A flare-up on your Smoke hollow Grill is often due to grease build-up or excessive fat in the meat. To resolve this, clean the grill or trim fat from meat before grilling.
B
Bob CookAug 25, 2025
What to do if I have a persistent grease fire in my Smoke hollow 105 Grill?
- M
  mrobinsonAug 25, 2025
  If you have a persistent grease fire in your Smoke hollow Grill, it's likely due to grease trapped around the burner system. To address this, turn the Regulator Knob to the “Off” position and then remove the LP Gas Cylinder. Carefully open the hood and allow the fire to burn out. Once the grill has cooled down, remove and clean all of its parts.
J
jessica18Aug 28, 2025
What causes flashback in Smoke hollow Grill?
- K
  Kristi ColeAug 28, 2025
  If you experience a flashback (fire in or around the Venturi tubes) in your Smoke hollow Grill, it's likely due to a clogged or blocked Venturi tube. If it's safe to do so, turn the Regulator Knob to the “Off” position and then remove the LP Gas Cylinder. After the grill has cooled down, clean the Burner and Venturi tubes.
T
tony34Aug 30, 2025
Why do the flames keep blowing out on my Smoke hollow 105?
- A
  Adam GordonAug 30, 2025
  If the flames on your Smoke hollow Grill blow out, it could be due to high or gusting winds, or low gas in the LP cylinder. Turn the front of the grill away from the wind or increase the flame height. If the gas is low, purchase a new 1 lb. LP Gas Cylinder.
R
Richard ElliottSep 2, 2025
What to do if Smoke hollow Grill burners will not light with a match?
- M
  mosesjanetSep 3, 2025
  If the burners on your Smoke hollow Grill won't light using a match, several factors could be the cause. Ensure the burners are correctly assembled. Also, verify that the LP gas cylinder isn't empty and is fully attached to the regulator. Check for obstructions in the burners. If the LP Gas Cylinder is empty, purchase a new one. Tighten the cylinder by hand if it is not fully attached to the regulator.
C
callenSep 6, 2025
Why is the flame so low on my Smoke hollow 105 Grill?
- D
  deborahholderSep 6, 2025
  A low flame or low heat on your Smoke hollow Grill is often due to low LP gas in the LP Gas Cylinder. Purchase a new 1 lb. LP Gas Cylinder.
I
ikennedySep 9, 2025
Why is gas leaking from my Smoke hollow 105 LP Gas Cylinder?
- M
  Maurice FisherSep 9, 2025
  Gas leaking from the LP Gas Cylinder of your Smoke hollow Grill is likely due to mechanical failure caused by rust or mishandling. Replace the LP Gas Cylinder.
V
Vickie WhiteSep 12, 2025
What to do if gas leaking between LP Gas Cylinder and Regulator connection on Smoke hollow Grill?
- I
  irussellSep 12, 2025
  Gas leaking between the LP Gas Cylinder and Regulator connection on your Smoke hollow Grill can be due to improper installation, a connection that isn't tight, or a failure of the seal on the LP Gas Cylinder. Remove the LP Gas Cylinder, reinstall it correctly, and tighten it. If the cylinder is damaged, replace it.
J
jonesbryanNov 18, 2025
What to do if my Smoke hollow Grill burners will not light using the ignitor?
- K
  Katie WilliamsNov 18, 2025
  If the burners on your Smoke hollow Grill won't light using the ignitor, several factors could be at play. Ensure the burners are correctly assembled. Confirm you're pressing the igniter sufficiently to create a spark. Check for a displaced, loose, or broken spark. Also, verify that the LP gas cylinder isn't empty and is fully attached to the regulator. Obstructions in the burners or wet electrodes and burners can also prevent ignition. Lastly, check the wire for looseness, disconnection, or shorting. Try pushing the Regulator Knob and turning it counterclockwise to the “High” position, then depress the Igniter Button until a loud click is heard. Repeat until the Burner lights. If the electrode tip is bent, bend it back to a 3/16” gap to the burner. Tighten Electrode mounting screws or rec...