socomec DIRIS Digiware I-30 User Manual

DIRIS Digiware
Measuring and monitoring system with
associated current sensors for electrical
installation
EN
INSTRUCT
I
ON
MANUAL
L1
L2
L3
N
www.socomec.com/
en/diris-digiware

socomec DIRIS Digiware I-30 Specifications

General

Brand	socomec
Model	DIRIS Digiware I-30
Category	Measuring Instruments
Language	English

Summary

2. HAZARDS AND WARNINGS

2.1. Risk of electrocution, burns or explosion

Details risks associated with electrical hazards, burns, or explosions during device operation.

2.2. Risk of damaging the device

Outlines precautions to prevent damage to the device during installation and use.

5. INSTALLATION

5.1. Recommendations and safety

Provides essential safety recommendations before installing DIRIS Digiware.

5.2. DIRIS Digiware mounting

Details how to mount the main DIRIS Digiware modules.

5.2.1. DIRIS Digiware C, U, I-3x, I-6x, IO-x - DIN rail-mounting

Instructions for DIN rail mounting of DIRIS Digiware C, U, I-3x, I-6x, IO-x modules.

5.2.3. DIRIS Digiware I-4x - DIN rail mounting

Instructions for DIN rail mounting of DIRIS Digiware I-4x modules.

5.2.4. DIRIS Digiware I-4x - back-plate mounting

5.3. Installing TE solid-core sensors

5.3.2. DIN rail mounting

5.3.3. Plate mounting

5.3.4. Installing on a cable with clamping collar

5.3.5. Bar mounting

5.4. Installing TR split-core sensors

5.5. Installing TF Flexible sensors

6. CONNECTION

6.1. DIRIS Digiware connection

Details the connection of the main DIRIS Digiware modules and power supply.

6.2. Connecting the current sensors

Explains how to connect the various types of current sensors.

6.3. Connecting to the electrical network and loads

Guides connection to single-phase, two-phase, and three-phase networks and loads.

7. DIGIWARE BUS

7.1. Principle

7.2. Sizing of the power supply

Guidance on sizing the power supply for the DIRIS Digiware system.

7.2.2. Calculation rules for the max. number of devices on the Digiware BUS

Rules for calculating the maximum number of devices on the Digiware BUS.

9. COMMUNICATION

9.1. General information

9.2. RS485 and Bus DIRIS Digiware rules

Rules for connecting DIRIS Digiware using RS485 communication.

9.2.1. Connection with the DIRIS Digiware C-31 system interface module

9.2.2. Connection with the DIRIS Digiware D-50/D-70 remote display

9.2.3. Connection with the DIRIS Digiware D-40 remote display

10. CONFIGURATION

10.1. Configuration using Easy Config

Describes configuration methods using the Easy Config software.

10.1.1. Connection modes

Details different connection modes for Easy Config software.

10.1.2. Using Easy Config

Step-by-step guide on using the Easy Config software for parameter setup.

10.2. Configuration from the DIRIS Digiware D remote display

Details configuration procedures using the DIRIS Digiware D remote display.

11. ALARMS

11.1. Alarms upon events

Explains how alarms are generated upon various events.

11.1.1. Electrical parameters

11.1.2. Voltage and current unbalance (in a three-phase network)

11.1.3. EN 50160 voltage quality events

11.1.4. Consumption

11.1.5. Digital inputs

11.2. System alarms

11.3. Setting up alarms

Explains how to configure and identify alarms using Easy Config.

13. PERFORMANCE CLASSES

13.1. Specification of the characteristics

Details the performance characteristics and classes of DIRIS Digiware.

13.2. Evaluation of the power supply quality