What to do if socomec ITY3-TW010B UPS shows power overload?
If your socomec UPS indicates a power overload, it means the power requirements of the connected equipment exceed the UPS capacity (more than 105% of nominal). To resolve this, disconnect some equipment from the UPS. The alarm will reset once the overload condition is no longer present.
Why is my socomec ITY3-TW010B in bypass mode?
Your socomec UPS may be in Bypass mode due to an overload, a fault, or a received command. When in Bypass mode, the equipment is powered but not protected by the UPS. Check for alarms related to over-temperature, overload, or forced bypass from a dry-in signal.
How to switch socomec ITY3-TW010B UPS to battery mode?
The socomec UPS switches to Battery mode automatically when a mains power failure occurs. While in this mode, the UPS is powering your equipment using battery power. It is recommended to prepare your equipment for shutdown.
What causes over-temperature warning on socomec UPS?
An over-temperature warning on your socomec UPS indicates that the internal temperature is too high. To resolve this, clear any obstructions from the vents, remove any nearby heat sources, and ensure that airflow around the UPS is not restricted. The UPS will continue to operate in its current state while the warning is active.
Why socomec ITY3-TW010B does not provide expected backup time?
If your socomec UPS isn't providing the expected backup time, the batteries may need charging or servicing. Connect the UPS to mains power for 48 hours to allow the batteries to charge. If the problem persists, contact your service representative.
What to do if socomec UPS shows battery fault?
If your socomec UPS displays a battery fault, it means the battery test has failed. This could be due to bad or disconnected batteries, or the battery minimum voltage being reached in Optimize Battery Management cycling mode. Check that all batteries are properly connected. You can start a new battery test. If the condition persists, contact your service representative.
Why socomec ITY3-TW010B UPS does not start?
If your socomec UPS doesn't start, the input source may not be connected correctly, or the Remote Power Off (RPO) switch might be active, or the RPO connector may be missing. Check the input connections and, if the UPS Status menu displays the 'Remote Power Off' notice, deactivate the RPO input.
What to do for over-temperature fault on socomec ITY3-TW010B?
If your socomec UPS indicates an over-temperature fault, the internal temperature is too high, causing the UPS to go to bypass or stop. Check the UPS ventilation and the ambient temperature to ensure they are within acceptable limits.
What does battery low mean on socomec ITY3-TW010B?
When your socomec UPS indicates 'Battery Low', it means the UPS is operating in Battery mode and the battery is running low. Note that the time to shutdown is approximate and may vary significantly.
What causes emergency power off on socomec UPS?
Emergency power off on your socomec UPS is activated when the RPO (Remote Power Off) is active. Check the RPO connector status to resolve this.
Details precautions and responsibilities regarding personal safety when using the UPS.
Covers enclosure rating, electrical protection, installation environment, and storage conditions.
Describes the UPS graphical LCD display, its buttons, and LED bar status meanings.
Explains the meaning of each area and icon displayed on the UPS LCD screen.
Lists configurable user settings, available options, and default values for the UPS.
Provides instructions on physical installation, clearances, and connections to power and loads.
Step-by-step guide on how to power on the UPS from the mains supply.
Instructions for starting the UPS directly from its batteries.
Lists common problems, their possible causes, and recommended actions for resolution.
General| Frequency | 50/60 Hz |
|---|---|
| Protection Level | IP20 |
| Apparent Power | 10 kVA |
| Active Power | 9 kW |
| Form Factor | Tower |
| Input Voltage | 400 V |
| Output Voltage | 230 V |
| Phase | 3-phase |
| Battery Type | VRLA |
| Battery Runtime | Depends on load |
| Efficiency | Up to 96% |
| Operating Temperature | 0 to 40°C |
| Communication Interface | RS232, USB |
| Technology | Double conversion online |
To Next Page