To Next PageTo Next PageWhat should I do if my SOLIS S6-GR1P6K shows UN-Vbatt?
If your SOLIS Inverter displays UN-Vbatt, restart the system to see if the fault clears. If the issue persists, it's recommended to contact the manufacturer's customer service for further assistance.
Why does my SOLIS S6-GR1P6K show NO-Battery, and how do I fix it?
If your SOLIS Inverter shows NO-Battery, check the information page to verify that the battery voltage is within the specified standards. Also, measure the battery voltage at the plug.
What to do if my SOLIS S6-GR1P6K Inverter displays GRID-INTF02 (1046 DATA:0000)?
If your SOLIS Inverter displays GRID-INTF02 (1046 DATA:0000), confirm whether the grid is seriously distorted and check whether the AC cable is connected reliably.
How to troubleshoot OV-TEM error on SOLIS Inverter?
If your SOLIS Inverter is showing an OV-TEM error, start by checking if the installation location meets the requirements specified in the user manual. Then, try to lower the ambient temperature around the inverter. After doing so, restart the inverter after fifteen minutes. If the error continues, contact the factory's customer service.
What does 'OV-Vbatt' mean on my SOLIS S6-GR1P6K and how to solve it?
The 'OV-Vbatt' error on your SOLIS Inverter indicates an over-voltage issue with the battery. Verify the battery voltage is within the specified standards. Also, measure the battery voltage at the inverter connection point. If problems persist, contact your battery manufacturer for service.
What does UN-TEM (103A DATA:0000) error mean on my SOLIS S6-GR1P6K Inverter?
If your SOLIS Inverter displays UN-TEM (103A DATA:0000), check the working environment temperature of the inverter. Restart the system to confirm if the fault continues.
What does LmtByEPM mean on my SOLIS S6-GR1P6K?
If your SOLIS Inverter is showing 'LmtByEPM', confirm the inverter is connected to an external EPM/meter to prevent reverse current. Also, check if the inverter is controlled by an external third-party device and verify if the power setting of the inverter power control is limited. You may also need to verify settings in section 6.6.7 and check your meter readings.
What does 'BatName-FAIL' mean on my SOLIS Inverter and how to resolve it?
If your SOLIS Inverter displays 'BatName-FAIL', confirm whether the battery model selection is consistent with the actual one.
How to fix ILeak-Check error on SOLIS Inverter?
If your SOLIS Inverter shows an ILeak-Check error, upgrade the software to the latest version. If the fault continues after the upgrade, contact the factory's customer service.
What to do if SOLIS Inverter displays OV-ILLC (1052 DATA:0000)?
If your SOLIS Inverter displays OV-ILLC (1052 DATA:0000), it may be due to an overloaded backup load. Check whether the backup load is overloaded. If the problem continues, restart the system to see if the fault clears.
General| Model | S6-GR1P6K |
|---|---|
| Rated Output Power | 6000 W |
| Max. Input Voltage | 600 V |
| Start-up Voltage | 90 V |
| Number of MPPT Trackers | 2 |
| MPPT Efficiency | 99.9% |
| Nominal AC Output Power | 6000 W |
| Nominal AC Voltage | 230 V |
| AC Voltage Range | 180-280 V |
| Nominal Grid Frequency | 50/60 Hz |
| THDi | <3% |
| DC Connection Type | MC4 |
| Protection Degree | IP65 |
| Topology | Transformerless |
| Cooling Method | Natural convection |
| Max. DC Input Power | 9000 W |
| Max. AC Apparent Power | 6000 VA |
| Operating Temperature Range | -25°C to 60°C |
| Type | Single-phase inverter |
