Solo 526M User Manual (English)

Questions and Answers:

C
Carlos SalazarAug 15, 2025
What to do if my Solo 526M Lawn Mower does not cut the grass completely?
- P
  Phillip HolmesAug 15, 2025
  If your Solo Lawn Mower is not cutting grass completely, there might be a few reasons. Check if your forward speed is too high and decrease it. Ensure the engine speed is at maximum. If the grass is too long, try going over it twice, changing the cutting height. Also, examine the flails for wear or breakage and replace them if necessary. Lastly, check for any grass build-up inside the flail housing and clean it.
M
Maria PierceAug 18, 2025
Why is the grass ejection insufficient on my Solo 526M Lawn Mower?
- V
  Vanessa HornAug 18, 2025
  If your Solo Lawn Mower isn't ejecting grass effectively, several factors could be at play. First, ensure the grass isn't wet; wait for it to dry. If the grass is too long, try going over it twice, adjusting the cutting height. Also, check that the cutting height isn't too low and increase it if needed. Make sure the engine is running at maximum speed and that your forward speed isn't too high—decrease it if it is. Finally, inspect the flail housing for any grass build-up and clean it out.
M
Martha MorganAug 21, 2025
Why does the engine overload during work operations with my Solo 526M?
- K
  keithjacksonAug 21, 2025
  If your Solo Lawn Mower engine overloads during operation, several factors could be the cause. First, ensure the engine speed is set to maximum. If the flails are worn, either invert or replace them. Check that your forward speed isn't too high and decrease it if necessary. Remove any grass snarls or build-up from the rotor. If the grass is too long, go over it twice, adjusting the cutting height. Lastly, ensure the cutting height isn't too low and increase it if needed.
L
Luke ParkAug 25, 2025
How to prevent my Solo Lawn Mower from scalping the ground?
- M
  Mr. Justin FischerAug 26, 2025
  If your Solo Lawn Mower is scalping the ground, the cutting height might be too low; increase it. If you are mowing on undulating terrain, try changing your cutting pattern, such as altering the direction. Also, if the ground is uneven, raising the cutting height can help.
D
Dennis HallAug 28, 2025
Why does my Solo Lawn Mower vibrate excessively?
- V
  vbutlerAug 28, 2025
  If your Solo Lawn Mower is vibrating excessively, start by checking for any grass build-up inside the flail housing and clean it. Inspect the belt for damage and replace it if needed. Examine the flails for bends or breaks and replace them if necessary. Lastly, if the flail rotor is warped, replace it.
J
Jerry JonesSep 1, 2025
Why does the cutting unit of my Solo 526M project objects outwards?
- D
  Donald JohnsonSep 1, 2025
  If the cutting unit of your Solo Lawn Mower is projecting objects outwards, make sure the front guard is lowered. Ensure the front cover is firmly closed. Only operate the machine in forward gear.
D
David HayesSep 4, 2025
What to do if the belt slips on my Solo Lawn Mower?
- R
  Rodney FletcherSep 4, 2025
  If the belt on your Solo Lawn Mower is slipping, first adjust the belt tension. If there's a build-up of grass inside the flail housing, clean it out. If the belt is worn, replace it.
S
stevenfisherSep 7, 2025
Why does my Solo Lawn Mower tend to run away on steep banks?
- M
  Matthew BaileySep 7, 2025
  If your Solo Lawn Mower tends to run away on steep banks, it could be due to the ground being too soft; wait until it dries. Also, ensure you are working in the direction of the bank, not at right angles to it.
C
Connie EdwardsSep 12, 2025
Why is the engine sluggish at switch on for my Solo 526M Lawn Mower?
- P
  Paul HamiltonSep 12, 2025
  If your Solo Lawn Mower engine feels sluggish when you switch it on, make sure the accelerator is in the start-up position. If the engine is cold, close the choke. Check the fuel tank and remove any water or sediment. Ensure that the feed cock is open to eliminate air bubbles or water in the petrol lines. Use oil with a viscosity suited to the temperature to prevent thick oil from hindering rotation. If the winding or start mechanism is faulty, replace it. Finally, inspect the spark plug, and clean or replace it, adjusting the electrode distance.