Solt GGSSL60DR2S - Cleaning the Grease Filters; Changing Charcoal Filter; Light Replacement

13
Cleaning the grease filters (recommended every two months)
Keeping this filters clean will keep the rangehood extraction performance at an optimum.
Ensure you never use a corrosive detergent during cleaning.
• The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage
• Put the filter into 40–50°C clean water with a small amount of regular dishwashing liquid, and soak for 2–3 minutes.
Wear gloves and clean with a soft brush. They can be washed in a dishwasher.
• Pull the comfort panels to open them.
• Remove the filters one by one pushing them towards the back side of the rangehood unit and simultaneously
pulling downwards.
• Avoid applying too much pressure, as the filter is delicate and will damage easy.
• Ensure that they are completely dry before refitting them back into place.
(The colour of the filter surface may change throughout the time but this has no impact to the filter efficiency)
• When fitting the filters into the hood pay attention that they are mounted in correct position the handle
facing outwards.
• Close the comfort panel.
Changing the charcoal filter (recirculation version)
These filters are not washable and cannot be regenerated, and must be replaced approximately every 4 months of
operation, or more frequently with heavy usage.
• Remove the metal grease filters
• Remove the saturated activated charcoal filter.
• Fit the new filters.
• Replace the metal grease filters.
Light replacement
Lightning inside the appliance is provided by a 1.5W LED light.
To replace the LED light:
1. Disconnect the appliance from the mains or switch off the circuit breaker.
2. Remove the metal filters (see Cleaning the grease filters).
3. Remove the light by levering its fitting from the hood body (this may require
pressure or force to be applied) and disconnect the connector of the light.
4. Replace the light with a n ew one of the same type, making sure that you
connect the light with the light cable correctly.
5. Install the metal filter back in place.
Cleaning and Maintenance (continued)
GREASE FILTERS
CLEANING METAL SELF-SUPPORTING GREASE FILTERS
 The filters must be cleaned every 2 months of operation, or
more frequently for particularly heavy usage, and can be
washed in a dishwasher.
 Pull the comfort panels to open them.
 Remove the filters one by one pushing them towards the back
side of the hood unit and simultaneously pulling downwards.
 Any kind of bending of the filters has to be avoided when
washing them. Before fitting them again into the hood make sure
that they are completely dry. (The color of the filter surface may
change throughout the time but this has no influence to the filter
efficiency).
 When fitting the filters into the hood pay attention that they are
mounted in correct position the handle facing outwards.
Close the comfort panel.
ACTIVATED CHARCOAL FILTER (RECIRCULATION VERSION)
These filters are not washable and cannot be regenerated, and must be replaced approximately
every 4 months of operation, or more frequently with heavy usage.

REPLACING THE ACTIVATED CHARCOAL FILTER
 Remove the metal grease filters
 Remove the saturated activated charcoal filter.
 Fit the new filters.
 Replace the metal grease filters.
9
DISPOSAL OF OLD ELECTRICAL APPLIANCES
The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain,
and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the
appliance, it must be separately collected.
Consumers should contact their local authority or retailer for information concerning the correct disposal of their old
appliance.
LIGHTING
LIGHT REPLACEMENT
1. Disconnect the appliance from the mains or switch off the circuit breaker.
2. Remove the metal filters (see Cleaning and Replacing Filters) .
3. Remove the light by levering its fitting from the hood body(this may require pressure or
force to be applied) and disconnect the connector of the light.
4. Replace the light with a n ew one of the same type, making sure that you connect the light
with the light cable correctly.
5. Install the metal filter back in place.
Changing the light
Lightning inside the appliance is provided by a 1.5W LED light.
To replace the LED light, proceed as follows:
Self-ballasted
LED modules
DBS-1.5-
H-33.2/120
Max power Voltage Picture Lamp Cap ILCOS D code
1.5W
Square/Diameter:33.2mmx120mm
/
220-240V
10
DISPOSAL OF OLD ELECTRICAL APPLIANCES
The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain,
and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the
appliance, it must be separately collected.
Consumers should contact their local authority or retailer for information concerning the correct disposal of their old
appliance.
LIGHTING
LIGHT REPLACEMENT
1. Disconnect the appliance from the mains or switch off the circuit breaker.
2. Remove the metal filters (see Cleaning and Replacing Filters) .
3. Remove the light by levering its fitting from the hood body(this may require pressure or
force to be applied) and disconnect the connector of the light.
4. Replace the light with a n ew one of the same type, making sure that you connect the light
with the light cable correctly.
5. Install the metal filter back in place.
Changing the light
Lightning inside the appliance is provided by a 1.5W LED light.
To replace the LED light, proceed as follows:
Self-ballasted
LED modules
DBS-1.5-
H-33.2/120
Max power Voltage Picture Lamp Cap ILCOS D code
1.5W
Square/Diameter:33.2mmx120mm
/
220-240V
10
DISPOSAL OF OLD ELECTRICAL APPLIANCES
The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain,
and reduce the impact on human health and the environment.
The crossed out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the
appliance, it must be separately collected.
Consumers should contact their local authority or retailer for information concerning the correct disposal of their old
appliance.
LIGHTING
LIGHT REPLACEMENT
1. Disconnect the appliance from the mains or switch off the circuit breaker.
2. Remove the metal filters (see Cleaning and Replacing Filters) .
3. Remove the light by levering its fitting from the hood body(this may require pressure or
force to be applied) and disconnect the connector of the light.
4. Replace the light with a n ew one of the same type, making sure that you connect the light
with the light cable correctly.
5. Install the metal filter back in place.
Changing the light
Lightning inside the appliance is provided by a 1.5W LED light.
To replace the LED light, proceed as follows:
Self-ballasted
LED modules
DBS-1.5-
H-33.2/120
Max power Voltage Picture Lamp Cap ILCOS D code
1.5W
Square/Diameter:33.2mmx120mm
/
220-240V
10