Sony DWA-01D Brochure & Specs

12 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

DWT-B01

DWR-S01D

DWA-01D

Digital Wireless Microphone System

Table of Contents

Other manuals for Sony DWA-01D

Operating Instructions83 pages

Quick Manual12 pages

Questions and Answers:

C
Carlos WolfeAug 7, 2025
What to do if there is no audio output to the PHONES connector on my Sony Adapter?
- A
  Aaron TurnerAug 7, 2025
  If there's no audio from the PHONES connector on your Sony Adapter, there might be a few reasons. First, check if the monitor level control is turned down and adjust it accordingly. Also, verify that the tuner currently turned on is selected by the monitor output selector, checking the POWER switch for the corresponding tuner of the DWR-S01D. Lastly, if the WRR-855 is attached and the monitor output selector is set to 2, remember the WRR-855 is a single-channel receiver, so no audio will output in that setting.
J
James SchneiderAug 11, 2025
Why is there noise in the audio output from the digital device connected to my Sony Adapter?
- E
  elizabeth28Aug 11, 2025
  If you are experiencing noise in the audio output from the digital device connected to your Sony Adapter, it could be due to synchronization issues. If your connected device isn't compatible with asynchronous input, synchronize the device using the word clock signal. Also, ensure the WORD SYNC connector is properly terminated with 75-ohm, especially if the DWR-S01D inserted in the adapter is the end device or the master word clock signal is input to this adapter only. You can add the 75-ohm termination using the UTILITY menu of the DWR-S01D.
S
Stephanie YorkAug 15, 2025
How to fix a Sony Adapter when the DWR-S01D or the WRR-855 does not turn on?
- J
  Jose ReillyAug 15, 2025
  If the DWR-S01D or the WRR-855 isn't turning on with your Sony Adapter, ensure it's correctly and completely inserted into the slot. Secure it using the mounting screws after inserting it firmly.
S
sharon93Aug 20, 2025
What to do if no signal is output from the OUTPUT2 connector when connecting my Sony Adapter to an analog device?
- S
  Steven WarrenAug 20, 2025
  If no signal is output from the OUTPUT2 connector of your Sony Adapter when connected to a device that accepts analog signals, first, check if the tuner 2 of the DWR- S01D is turned on. Note that the manual does not provide a solution if the WRR-855 is attached to the adapter.
M
Michael ClarkAug 25, 2025
Why is audio from tuner 2 mixed with tuner 1 on my Sony Adapter when the monitor output selector is set to 1?
- F
  fjacksonAug 25, 2025
  If audio from tuner 2 is mixing with audio from tuner 1 when the monitor output selector is set to 1 on your Sony Adapter, it's likely because “RX1+2” is selected on the ANALOG OUTPUT1 function of the DWR-S01D. To resolve this, on the DWR-S01D, select “RX1” on the ANALOG OUTPU1 function of the UTILITY menu. When “RX1+2” is selected, audio from tuner 1 and 2 are mixed regardless of the monitor output selection.
A
Antonio BoyleAug 28, 2025
What to do if no signal is output from the OUTPUT2 connector of my Sony Adapter when connected to a digital device?
- M
  Mark TorresAug 28, 2025
  If there is no signal output from the OUTPUT2 connector on your Sony Adapter when connected to a device that accepts digital signals, check the ANALOG AES/EBU selector. If it's set to ANALOG, change it to AES/EBU.
T
Tommy PerezSep 2, 2025
Why is there noise in the analog signal output from the OUTPUT2 connector of my Sony Adapter?
- Z
  zachary20Sep 2, 2025
  If you're experiencing noise in the analog signal output from the OUTPUT2 connector of your Sony Adapter when it's connected to a device that accepts analog signals only, check the ANALOG AES/EBU selector. If it is set to AES/ EBU, set it to ANALOG.

Sony DWA-01D Specifications

General

Brand	Sony
Model	DWA-01D
Category	Microphone system
Language	English

Related product manuals

Preview: Sony UWP-D21

Preview: Sony AU

Preview: Sony UWP Series

Sony UWP Series

Preview: Sony UWP-V1