To Next PageTo Next Page
Need help?Do you have a question about the Sony HBD-E870 and is the answer not in the manual?
Details specifications for the amplifier section including power output and distortion.
Lists the outputs available in the video section.
Specifies supported signal formats for BD/DVD/Super Audio CD/CD systems.
Details specifications for the USB port, including maximum current.
Describes the tuner section system, specifically PLL quartz-locked digital synthesizer.
Provides general specifications such as power requirements, consumption, dimensions, and mass.
Notes on replacing chip components, including handling and precautions for tantalum capacitors.
Guidelines for repairing flexible circuit boards, focusing on soldering iron temperature and handling.
Outlines the safety check procedures required after service before releasing the set.
Explains methods for testing AC leakage current from exposed metal parts to earth ground.
Highlights components critical to safe operation, requiring replacement with specified Sony parts.
Precautions for handling the optical pick-up block, including electrostatic discharge and flexible board care.
Guidelines for safely checking the laser diode emission, specifying distance from the objective lens.
Information on unleaded solder, its characteristics, and handling procedures.
Notes on replacing chip components, emphasizing not reusing disconnected parts and avoiding damage to tantalum capacitors.
Guidelines for repairing flexible circuit boards, including temperature control and conductor protection.
Procedure to release the disc tray lock for demonstration discs.
Flowchart for checking the drive section, including reproduction and voltage checks.
Flowchart for checking the optical device IOP value via service mode.
A flowchart illustrating the order of disassembly steps for various unit components.
Detailed steps for removing the outer case (EZ) of the unit.
Procedure to reset the system to initial conditions, clearing RAM data except BD/DVD data.
Instructions for activating demo mode, which locks the disc tray and prevents ejection.
Procedure to change the S-AIR ID setting, cycling through A, B, and C.
Steps for performing a panel test, which involves lighting up indicator tube segments and displaying model information.
Procedure to enter the amplifier test mode and check various parameters like microphone input and volume settings.
Method for entering the BD service mode, which allows access to functions like error log, diagnostics, and factory initialization.
Options within the Diag menu, including Device Test, Video Test, and Audio Test.
Options within the Log menu, primarily for displaying error logs.
Function to restore the set to its factory default settings.
Options for network diagnostics, including Ifconfig and Ping tests.
Information that the Version Up function is not used.
Displays system information, including software and drive details.
Indicates that the EMC Test Mode is not used.
Options within the Drive menu for writing OP data and checking the drive.
Lists the categories available for device testing within the Diag menu.
Describes how to select specific devices for testing within the Diag menu.
Details how to perform video and audio tests, including color bar output and tone sound generation.
Shows basic system information, with a go-to screen 2 for drive information.
Details drive information, including DIOP measurements, which may affect the version up function.
How to select items from the main service menu.
How to select specific test items from the Drive menu.
Procedure to write OP data into the flash IC using a USB storage device.
Notes that this menu is not used for servicing.
Notes that this menu is not used for servicing.
Confirms playback operation using test discs like BLX-104/204 and CD (HLX-A1).
Procedure to confirm network connection by checking IP address and status.
Block diagram illustrating the servo section of the unit.
Block diagram illustrating the memory section of the unit.
Block diagram showing the tuner and S-AIR sections of the unit.
Block diagram illustrating the audio section, including digital audio interface and power amplifiers.
Block diagram detailing the various voltage regulators and power control circuits.
Block diagram illustrating the panel and power supply sections, including system controller and power control.
Exploded view of the case and front panel section, showing part numbers and assembly.
Exploded view of the MB-134 board assembly, detailing part numbers and their locations.
Exploded view of the back panel section, showing components like the BD drive and connectors.
Exploded view of the main board assembly, illustrating power board, audio board, and wire connections.
Exploded view of the BD drive section (BPX-5), showing optical device, wires, and holder replacement.
List of capacitors with part numbers, descriptions, tolerance, voltage, and type.
List of connectors with part numbers and descriptions.
List of diodes with part numbers and descriptions.
List of integrated circuits with part numbers and descriptions.
List of jacks with part numbers and descriptions.
List of coils with part numbers and descriptions.
List of transistors with part numbers and descriptions.
List of resistors with part numbers, descriptions, tolerance, wattage, and type.
List of capacitors for the Audio, Connect, and FL boards.
List of connectors for the Audio, Connect, and FL boards.
List of diodes for the Audio, Connect, and FL boards.
List of integrated circuits for the Audio, Connect, and FL boards.
List of coils for the Audio, Connect, and FL boards.
List of transistors for the Audio, Connect, and FL boards.
General
