Sony HCD-FR1 User Manual

SERVICE MANUAL
Sony Corporation
Audio Group
Published by Sony Engineering Corporation
US Model
HCD-FR1/FR8/FR9
Canadian Model
HCD-FR1
SACD/DVD RECEIVER
9-879-011-08
2005G16-1
© 2005.07
Ver. 1.7 2005.07
SPECIFICATIONS
HCD-FR1/FR8/FR9
HCD-FR1/FR8/FR9 are the amplifier, DVD/
SACD and tuner section in DAV-FR1/FR8/FR9.
Model Name Using Similar Mechanism NEW
Mechanism Type CDM69-DVBU16
Optical Pick-up Name DBU-1
PHOTO: HCD-FR1
AUDIO POWER SPECIFICATIONS POWER
OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 4 ohm loads, both channels driven, from 20 –
20,000 Hz; rated 75 watts per channel minimum RMS
power, with no more than 0.7 % total harmonic
distortion. (from 250 milli watts to rated output)
Amplifier section (HCD-FR1)
Surround mode Front: 110 W + 110 W
(reference) (with SS-TS20)
music power output Center*:
110 W
(with SS-CT44)
Surround*:
110 W +
110 W
(with SS-TS20)
Subwoofer*:
100 W 2
×
×
(with SS-WS12)
Amplifier section (HCD-FR8)
Surround mode Front: 114 W + 114 W
(reference) (with SS-TS21)
music power output Center*:
114 W
(with SS-CT33)
Surround*:
114 W +
114 W
(with SS-TS20)
Subwoofer*:
115 W 2
(with SS-WS12)
Amplifier section (HCD-FR9)
Surround mode Front: 114 W + 114 W
(reference) (with SS-TS21)
music power output Center*:
114 W
(with SS-CT33)
×
Surround*:
114 W +
114 W
(with SS-TS21)
Subwoofer*:
115 W
2
(with SS-WS12)
*Depending on the sound field settings and the source,
there may be no sound output.
Inputs VIDEO/SAT:
Sensitivity: 250 mV/
450 mV
Impedance: 50 kilohms
Output SURROUND BACK
Voltage: 2V
Impedance: 1 kilohms
Phones Accepts low-and high-
impedance headphones.
Super Audio CD/DVD system
Laser Semiconductor laser
(Super Audio CD/DVD:

= 650 nm)
(CD: λ
λ
= 780 nm)
Emission duration:
continuous
Signal format system NTSC
Frequency response (at 2 CH STEREO mode)
DVD (PCM): 2 Hz to 22
kHz (±1.0 dB)
CD: 2 Hz to 20 kHz (±1.0
dB)
Harmonic distortion Less than 0.03 %
Tuner section
System PLL quartz-locked digital
synthesizer system
FM tuner section
Tuning range 87.5 – 108.0 MHz
(100 kHz step)
Antenna (aerial) FM wire antenna (aerial)
Antenna (aerial) terminals
75 ohms, unbalanced
Intermediate frequency 10.7 MHz
AM tuner section
Tuning range 531 – 1,710 kHz (with the
interval set at 9 kHz)
530 – 1,710 kHz (with the
interval set at 10 kHz)
Antenna (aerial)
Intermediate frequency
Video section
Outputs
General
Power requirements
Power consumption
Dimensions (approx.)
Mass (approx.)
AM loop antenna (aerial)
450 kHz
Video: 1 Vp-p 75 ohms\
S VIDEO:
Y: 1 Vp-p 75 ohms
C: 0.286 Vp-p 75 ohms
COMPONENT:
Y: 1 Vp-p 75 ohms
PB/CB, PR/CR: 0.65 Vp-p
75 ohms
× ×
120 V AC, 60 Hz
120 W
430 × 70 × 398 mm
(17 2
7
/ 8 15
3
/ 4 inches)
(w/h/d) incl. projecting
parts
5.5 kg (12 lb 12 oz)
Design and specifications are subject to change
without notice.

Sony HCD-FR1 Specifications

General

Number of Channels	2
Bluetooth	No
Frequency Response	20 Hz - 20 kHz
Power Output	50W + 50W (4 ohms, 1 kHz, 10% THD)
Tuner Type	FM/AM
Output Power	50W + 50W (4 ohms, 1 kHz, 10% THD)

Summary

SPECIFICATIONS

AUDIO POWER SPECIFICATIONS

Details audio output power and total harmonic distortion.

Amplifier Sections

Power output specifications for amplifier sections HCD-FR1, FR8, FR9.

General Specifications

Includes power requirements, consumption, dimensions, and mass.

SERVICING NOTE

Handling Optical Pick-up and Flexible Boards

Precautions for handling delicate optical pick-up and flexible boards.

Laser Diode Emission Check

Safe procedure for checking laser diode emission.

Model Identification

Identifies models by part number and model name.

GENERAL

Front Panel Layout

Identifies controls and connectors on the front panel.

Rear Panel Layout

Identifies connectors and jacks on the rear panel.

DIAGRAMS

Circuit Board Locations

Illustrates the physical placement of various circuit boards.

RF Board (Printed Wiring & Schematic)

Physical layout and circuit diagram for the RF board.

DMB08 Board (Printed Wiring & Schematic)

Physical layout and circuit diagrams for the DMB08 board.

AMP Board (Printed Wiring & Schematic)

Physical layout and circuit diagrams for the AMP board.

IO Board (Printed Wiring & Schematic)

Physical layout and circuit diagrams for the IO board.

EXPLODED VIEWS

Case Section Exploded View

Exploded view of the case section with part numbers.

Front Panel Section Exploded View

Exploded view of the front panel section with part numbers.

Mechanism Deck Sections Exploded Views

Exploded views of the mechanism deck sections 1-6.

ELECTRICAL PARTS LIST

Amplifier Section Parts

List of electrical components for the amplifier section.

DMB08 Board Parts

List of electrical components for the DMB08 board.

IO Board Parts

List of electrical components for the IO board.

SUPPLEMENT-1: TEST MODE AND ELECTRICAL ADJUSTMENT

SECTION 1 TEST MODE

Accesses various diagnostic and operational test modes.

SECTION 2 ELECTRICAL ADJUSTMENT

Procedures for electrical adjustments and servo calibration.

SUPPLEMENT-2: DISASSEMBLY, ASSEMBLY, BLOCK DIAGRAMS, IC DIAGRAMS & PIN FUNCTIONS

SECTION 1 DISASSEMBLY

Step-by-step procedure for disassembling the set.

IC Block Diagrams

Diagrams illustrating the internal structure of key integrated circuits.

IC Pin Function Description

Detailed description of each pin's function for key ICs.

SUPPLEMENT-3: TACTILE SWITCH REPLACEMENT NOTES

Servicing Notes on Tactile Switches

Information on selecting tactile switches based on board suffixes.

Tactile Switch Part Number Reference

Table correlating board suffixes with specific tactile switch part numbers.