– 24 –
6-1. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC301 µPD780016YGF-015-3BA (MASTER CONTROLLER)
SECTION 6
DIAGRAMS
Pin No. Pin Name I/O Function
1 TA-MUTE O
Line mute control signal output terminal “L”: mute on
2 DBFB-H/L O
DBFB normal/high selection signal output terminal “L”: DBFB high, “H”: DBFB low
3 427-LAT O
Serial data latch pulse output to the electrical volume (IC201)
4 K-CON-LAT O
Serial data latch pulse output to the key control (IC1401)
5 K-CON-ON O
On/off selection signal output of the key control circuit “L”: on
6 F-RELAY O
Relay drive signal output for the main speaker (front speaker) “H”: on
7 R-RELAY O
Relay drive signal output for the surround speaker “H”: on
8 PL-RELAY O
Relay drive signal output for the surround speaker “H”: on
9 TEST I
Connected to ground
10 X2 O
Main system clock output terminal (5 MHz)
11 X1 I
Main system clock input terminal (5 MHz)
12 VDD —
Power supply terminal (+5V)
13 XT2 O
Sub system clock output terminal (32.768 kHz)
14 XT1 I
Sub system clock input terminal (32.768 kHz)
15 RESET I
System reset signal input from the reset signal generator (IC302) “L”: reset For several
hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
16 (INT/IN) I
Connected to ground
17 (INT/IN/OUT) I
Connected to ground
18 SCOR O
Subcode sync (S0+S1) detection signal input terminal Not used (fixed at “L”)
19 SOFT-TEST O
Output terminal for the software test (open)
20 AC-CUT I
AC off detection signal input from the reset signal generator (IC302)
21 RDS-INT I
Serial data reading clock signal input for the radio data system Not used (fixed at “L”)
22 RDS-DATA I
Serial data input for the radio data system Not used (open)
23 VDD —
Power supply terminal (+5V)
24 AVDD —
Power supply terminal (+5V) (for A/D conversion)
25 ADJ I
Setting terminal for the test Normally: “H”
26 A-SHUT I
Shut off detection signal input from the deck-A reel pulse detector (Q1001)
27 B-SHUT I
Shut off detection signal input from the deck-B reel pulse detector (Q1002)
28 B-HALF I
Detection input from the deck-B half detect switch (S1007)
29 CLK-CHECK I
Not used (fixed at “L”)
30 SPEC-IN I
Setting terminal for the version Fixed at “L”
31 ADJ2 I
Setting terminal for the test Normally: “L”
32 DEMO-MODE I
Setting terminal for the demonstration H/L Fixed at “L”
33 AVSS —
Ground terminal (for A/D conversion)
34 SQ-DATA-IN I
Sub-code Q data input terminal Not used (fixed at “L”)
35 — —
Not used (open)
36 D.OUT ON/OFF O
Power on/off selection signal output for the CD digital out optical “H”: power on
37 SW-ON/OFF O
Not used (open)
38 FUNC1 I
Setting terminal for the function 1 Fixed at “L”
39 FUNC2 I
Setting terminal for the function 2 Fixed at “L”
40 VSS —
Ground terminal
41 VOL-LAT O
Serial data latch pulse output terminal Not used (open)
42 PL-LAT O
Serial data latch pulse output terminal Not used (open)
43 COM-DIN I
Serial data input terminal Not used (fixed at “L”)
44 COM-DOUT O
Serial data output to the electrical volume (IC201), DJ effect controller (IC401), and key
control (IC1401)
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com
To Next Page
Loading...
