Sony ICF-2001D - Memory Tuning and Broadcast Bands; Broadcast Band Scanning Setup; Station Memorization Procedure

BROADCAST BANDS
You can designate a broadcast band to be scanned from the follow-
ing,
by
pressing
the
SHIFT
key
and
the
corresponding
MEMORY
PRESET key.
Broadcast
band
LW
Frequency range to be
scanned
150 - 285 kHz
531 - 1620 kHz
(530 - 1620 kHz)
2250 - 2550 kHz
3150 - 3450 kHz
3850 - 4050 kHz
4700 5110 kHz
5900 - 6250 kHz
7000 - 7400 kHz
25m 11500 - 12150 kHz
19m 15000 - 15700 kHz
17450 - 18000 kHz
13 m 21350 - 21950 kHz
25570-26100 kHz
See 76.0 108.0 MHz
Page 1. 87.5. 108.0 MHz
* Not provided with certain models.
Scanning
interval
3 kHz
9 kHz
(10 kHz)
0.025 MHz
@The frequency ranges of the SW meter bands to be scanned are
somewhat wider than those indicated on the front panel of the
receiver. f
@The frequencies between two SW meter bands can be scanned
with the DEFINE scan at a 5 kHz scanning interval.
To check the frequency range to be scanned
Keeping the SHIFT key pressed, press the L1 (a-1) key or the L2 (a-2)
key. The lower limit frequency or the upper limit frequency appears
on the frequency display. : i as
@
The
selected
scanning
range
is
memorized
even
after
the
receiver
is
once
turned
off
or
the
station
beyond
the
range
is
tuned
in.
Notes
@ Since scanning stops with a stronger signal than the preset level,
it may stops a little before or after the exact frequency of a station.
If this happens, tune in the station precisely with the MANUAL
TUNING knob.
@When scanning does not stop at all during AM (LW, MW or SW)
reception, make sure the AM RF GAIN control (right side) is set to
MAX and the AM ATT selector (left side) is set to DX.
@When scanning stops at a noise or many unwanted stations dur-
ing AM reception, slide the AM RF GAIN control slightly toward
MIN. Then, set the AM ATT selector to LOCAL.
@ AM mode, scanning range setting, scan mode and MW scanning
interval cannot be changed during scanning.
ICF-2001D/2010
MEMORY TUNING
Once
the
frequencies
of
the
stations
are
memorized,
all
you
have
to
do
is
to
push
a
key.
Up
to
32
stations
can
be
memorized
to
the
a-1
to
d-8
MEMORY
PRESET
keys.
HOW TO MEMORIZE A STATION
The
numbers
in
the
illustration
refer
to
the
sequence
of
operations.
1 Set the MAIN POWER switch and the POWER switch to ON.
2 Tune in the desired station using any tuning method—direct tun-
ing
(page
9),
manual
tuning
(page
10)
or
scan
tuning
(page
14),
and set AM mode appropriately when receiving AM stations.
3 Keeping the ENTER key pressed, press one of the MEMORY
PRESET keys.
Indicates the station
is memorized to a-3 key.
a
Repeat steps 2 and 3 for each MEMORY PRESET key.
ENTER
WIDE
14D en
AM
@lf
you
memorize
another
station
to
a
key
to
which
you
have
already
memorized
a
station,
the
previous
station
will
be
erased.
You
cannot
erase
a
station
without
memorizing
another
station.
@AM
150
kHz
are
memorized
to
all
the
keys
at
the
factory.
Note
After
replacing
the
computer/clock
batteries,
be
sure
to
memorize
the
stations
again.
The
memory
contents
will
be
erased
when
the
batteries
are
removed.