000
5. Menu Display and Settings: Setup Menu List
59
Audio >Audio Input
Sets audio input settings.
Item Sub-item setting Description
INPUT2 MIC
Reference
–60dB / –50dB / –40dB Sets the reference recording level for XLR
microphone input from INPUT2.
CH1 Wind
Filter
On / Off Enables/disables the wind reduction filter for
channel 1 recording.
CH2 Wind
Filter
On / Off Enables/disables the wind reduction filter for
channel 2 recording.
CH3 Wind
Filter
On / Off Enables/disables the wind reduction filter for
channel 3 recording.
CH4 Wind
Filter
On / Off Enables/disables the wind reduction filter for
channel 4 recording.
CH3 Level
Control
Auto / Manual Selects automatic audio input level
adjustment or manual adjustment for
recording channel 3.
[Note]
If both CH3 Input Select and CH4 Input Select are
set to Internal MIC, CH4 is switched to automatic/
manual in conjunction with this setting.
CH4 Level
Control
Auto / Manual Selects automatic audio input level
adjustment or manual adjustment for
recording channel 4.
[Note]
If both CH3 Input Select and CH4 Input Select are
set to Internal MIC, CH4 is switched to automatic/
manual in conjunction with the CH3 Level Control
setting.
CH3 Input
Level
0 to 99 (49) Sets the audio input level for recording
channel 3.
[Note]
If both CH3 Input Select and CH4 Input Select are
set to Internal MIC, the CH4 Input Level is switched
in conjunction with this setting.
CH4 Input
Level
0 to 99 (49) Sets the audio input level for recording
channel 4.
[Note]
If both CH3 Input Select and CH4 Input Select are
set to Internal MIC, the CH4 Input Level is switched
in conjunction with the CH3 Input Level setting.
Audio >Audio Input
Sets audio input settings.
Item Sub-item setting Description
Audio Input
Level
0 to 99 Sets the audio input level.
Can be used as the master volume,
according to the settings of CH1 Level to
CH4 Level.
Limiter Mode Off / –6dB / –9dB / –12dB / –15dB / –17dB Selects the limiter characteristic for large
input signals when adjusting the audio input
level manually.
CH1&2 AGC
Mode
Mono / Stereo Sets the auto level adjustment mode for
recording channel 1 and channel 2.
CH3&4 AGC
Mode
Mono / Stereo Sets the auto level adjustment mode for
recording channel 3 and channel 4.
AGC Spec –6dB / –9dB / –12dB / –15dB /
–17dB
Selects the AGC characteristic.
1kHz Tone on
Color Bars
On / Off Turns the 1 kHz reference tone signal on/off
when displaying color bars.
[Note]
When set to On, the 1 kHz reference tone signal
is set for recording on channel 3 and channel 4,
even if CH3 Input Select and CH4 Input Select are
set to Off.
CH1 Level Input without XLR adaptor
Audio Input Level / Side / Level+Side
Input with XLR adaptor (page 40)
Audio Input Level / Through
Sets the combination of audio input level
adjustments enabled for recording channel
1.
[Note]
“Side” refers to the CH1 INPUT LEVEL dial on
the side of the camcorder. When Level+Side is
selected, the audio recording level is determined
by the combination of the Audio Input Level and
dial settings (page 95).
CH2 Level Input without XLR adaptor
Audio Input Level / Side / Level+Side
Input with XLR adaptor (page 40)
Audio Input Level / Through
Sets the combination of audio input level
adjustments enabled for recording channel
2.
[Note]
“Side” refers to the CH2 INPUT LEVEL dial on
the side of the camcorder. When Level+Side is
selected, the audio recording level is determined
by the combination of the Audio Input Level and
dial settings (page 95).
To Next Page
