4
MZ-RH1
SECTION 1
SERVICING NOTES
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
OPERATION CHECK WHEN THE MAIN BOARD IS
REMOVED
In making an operation check with the MAIN board removed from
the set, short the SL463 of the MAIN board with the solder before
starting the operation check.
Note: Be sure to remove the solder used for shortcircuit after the repaire
completed.
– MAIN Board (Conductor Side) –
SL463
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
NOTES ON REPLACEMENT OF CSP (CHIP SIZE
PACKAGE) IC
Replacement of IC401, IC501, IC601 and IC701 on the MAIN board
used in this set requires a special tool.
NOTES ON REPLACEMENT OF IC801 ON THE MAIN
BOARD
IC801 on the MAIN board can not be exchanged alone. When IC801
on the MAIN board is damaged, exchange the complete MAIN
board.
NOTES ON REPLACEMENT OF IC1 AND S8 ON
THE OLED BOARD
IC1 and S8 on the OLED board can not be exchanged alone. When
IC1 and S8 on the OLED board are damaged, exchange the complete
OLED board.
System requirements
The following system environment is required in order to use the SonicStage/MD Simple Burner
software.
Computer IBM PC/AT or Compatible
• CPU: Pentium III 450 MHz or higher
• Hard disk drive space: 200 MB or more (1.5 GB or more is recommended)
(The amount space will vary according to Windows version and the number
of music files stored on the hard disk.)
• RAM: 128 MB or more
Others • CD drive (capable of digital playback by WDM) (A CD-R/RW
drive is necessary for CD writing)
• Sound Board
• USB port
Operating
System
Factory installed:
Windows XP Media Center Edition 2005/Windows XP Media Center Edition
2004/Windows XP Media Center Edition/Windows XP Professional/Windows
XP Home Edition/Windows 2000 Professional (Service Pack 3 or later)/
Windows Millennium Edition/Windows 98 Second Edition
Display High Color (16 bit) or higher, 800
better is recommended)
Others • Internet access for online registration and CDDB use
• Internet access and Microsoft Internet Explorer (version 5.5 or higher) for use
of EMD services
• Windows Media Player (version 7.0 or higher) installed for playing WMA
files
This software is not supported by operating systems other than those listed above, custom-built
PCs, operating systems that are upgrades from the original manufacturer-installed system, multi-
boot environments, multi-monitor environments, or Macintosh computers.
Notes
• We do not ensure trouble-free operation on all computers that satisfy the system requirements.
• The NTFS format of Windows XP/Windows 2000 Professional can be used only with the standard (factory)
settings.
• We do not ensure trouble-free operation of the system suspend, sleep, or hibernation function on all computers.
To Next Page
Loading...
